35, 45 and 55 Agricultural Tractors Caterpillar


Transmission Hydraulic Control

Usage:

45 1DR



Illustration 1g00469001

The transmission hydraulic control group includes the speed clutch circuit, direction clutches, the pressure regulating valve, and modulation valves.

The transmission hydraulic control group includes the speed clutch circuit, direction clutches, the pressure regulating valve, and modulation valves.


NOTICE

Do not use caustic (corrosive) materials to clean any parts in this valve group. Caustic materials cause corrosion and damage to parts.


(1) Tighten the 3E-9865 Thin Stop Nut until the coil is snug and the nut will not rotate by hand. Do not tighten the nut to a torque that is greater than 11 N·m (8 lb ft).

(2) 114-5913 Solenoid Coil (6 volts)

Quantity ... eleven
Resistance at an ambient temperature of 20°C (68°F) ... 1.70 Ohms ± 4%

(3) 119-3913 Core Assembly

Quantity ... nine
Torque ... 40 to 54 N·m (30 to 40 lb ft)

(4) 114-5910 Solenoid Spring

Quantity ... nine
Free length after test ... 28.2 mm (1.11 inch)
Outside diameter ... 4.70 mm (.185 inch)

(5) 114-5922 Orifice Plate

Quantity ... one
Orifice size ... 0.51 mm (.020 inch)

(6) 114-5940 Screen Orifice

Quantity ... two
Orifice size ... 5.3 mm (.21 inch)

(7) 114-5926 Plug Orifice

Quantity ... two
Orifice size ... 0.64 ± 0.03 mm (.025 ± .001 inch)

(8) 114-5928 Modulator Spring

Quantity ... two
The modulating valve pressure is factory set. ... nonadjustable
Free length after test ... 34.3 mm (1.35 inch)
Outside diameter ... 16.8 mm (.66 inch)

(9) 114-5942 Screen Orifice

Quantity ... two
Orifice size ... 9.7 mm (.38 inch)

(10) 160-0589 Modulating Solenoid

Quantity ... two
Rated capacity ... 1.79 Ohms at 6 volts
Operating capacity ... 5 volts and 400 hertz

(11) 114-5920 Shim

Thickness ... 7.549 ± 0.074 mm (.2972 ± .0029 inch)
Outside diameter ... 16.26 mm (.640 inch)
Required pressure at 57°C (135°F) and 2100 rpm ... 1755 to 1895 kPa (255 to 275 psi)

Note: Add shims in order to increase pressure. Remove shims in order to decrease pressure.

(12) 114-5917 Regulator Spring

Quantity ... one
Free length after test ... 86.9 mm (3.42 inch)
Outside diameter ... 16.8 mm (.66 inch)

(13) 114-5916 Regulator Spring

Quantity ... one
Free length after test ... 89.7 mm (3.53 inch)
Outside diameter ... 25.1 mm (.99 inch)

Solenoid Valve Assemblies




Illustration 2g00288481

(1) (2) (3) (A) (B) (C) (F1) (F2) (REV) Direct operating solenoids:

Quantity ... nine
Rated capacity ... 1.79 Ohms at 6 volts
Operating capacity ... 6.5 volts, 100 hertz, and 67% of the duty cycle

(MC1) (MC2) Modulating solenoids

Quantity ... two
Rated capacity ... 1.79 Ohms at 6 volts
Operating capacity ... 5 volts and 400 hertz

Control Valve Assembly




Illustration 3g00288484

(1) Transmission pressure switch (low pressure)

Type ... normally closed
Operation ... 830 kPa (120 psi)
Fault ... critical shutdown

Caterpillar Information System:

938G Wheel Loader and IT38G Integrated Toolcarrier Steering System Relief Valve (Secondary Steering)
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System CAT data link
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Backup Alarm
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Start Relay
938G Wheel Loader and IT38G Integrated Toolcarrier Steering System Electric Drive Pump (Secondary Steering)
793B Off-Highway Truck Power Train Differential Pinion Bearing - Adjust
35, 45 and 55 Agricultural Tractors Transmission Input Shaft
Comfort Series Seat For Caterpillar Machines Mechanical Suspension With Variable Damper - Assemble
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Solenoid Valves
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Sensors
Comfort Series Seat For Caterpillar Machines Mechanical Suspension With Variable Damper - Disassemble
561M Pipelayer Power Train Oil Filter
793B Off-Highway Truck Power Train Differential and Bevel Gear - Adjust
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-650B and Barber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-225C Asphalt Pavers Burn Prevention
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Power Train Electronic Control System
793C Off-Highway Truck Power Train Transmission Hydraulic Control Pilot Pressure - Test
793C Off-Highway Truck Power Train Torque Converter Lockup Clutch Signal Pressure - Test
784B and 785B Off-Highway Truck/Tractor Hydraulic System Gear Pump (Torque Converter, Parking Brake Release, and Pulled Unit Brake Cooling)
3406E Truck Engine Exhaust Manifold Shield
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Electric Starting Motor - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Crankcase Breather
3406E Truck Engine Water Pump
561M Pipelayer Power Train Oil Cooler
784B and 785B Off-Highway Truck/Tractor Hydraulic System Gear Pump (Torque Converter and Parking Brake Release)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.