928G Wheel Loader Caterpillar


Starting Below 0°C (32°F) with Thermal Starting Aid

Usage:

928G 6XR

------ WARNING! ------

Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury.

----------------------

  1. Move both the transmission directional control lever and the direction control switch (if equipped) into NEUTRAL.

  1. Lift the steering column tilt lever and move the steering column to the desired position. Release the steering column tilt lever in order to lock the steering column into position.

  1. Engage the parking brake.

  1. Move the control levers to the HOLD position.

  1. Turn the engine start switch key to the ON position. Pause for three seconds so that the secondary steering self-test (if equipped) can test.



    Illustration 1g00101749

  1. Depress the top of the thermal starting aid switch. The light bar inside the switch will light.



    Illustration 2g00101750

  1. Wait until the light bar inside the switch goes out. While the throttle is in the fully open position, turn the engine start switch key in order to engage the starter motor. Do not crank the engine for more than 15 seconds.

  1. If the engine does not start, release the engine start switch key in order to disengage the starter motor. Repeat Steps 6 and 7.

    When the engine starts, continue to depress the starting aid switch until the engine runs evenly. Do not depress the starting aid switch for more than 30 seconds after the engine starts.

Caterpillar Information System:

928G Wheel Loader Starting Above 0°C (32°F)
416C, 426C, 428C, 436C and 438C Backhoe Loaders Seat Adjustment and Seat Belt Inspection
120H and 135H Motor Graders Air System and Brakes Check Valve (Parking Brake Release)
416C, 426C, 428C, 436C and 438C Backhoe Loaders Mounting and Dismounting
12H, 140H and 160H Motor Graders Air System and Brakes Stop Light Air Pressure Switch
143H and 163H Motor Graders Air System and Brakes Pressure Switch (Brake Air) (Parking Brake)
143H and 163H Motor Graders Air System and Brakes Pressure Switch (Low Brake Air)
12H, 140H and 160H Motor Graders Air System and Brakes Front Wiring
120H and 135H Motor Graders Air System and Brakes Front Wiring
120H and 135H Motor Graders Air System and Brakes Air Tank
966G and 972G Wheel Loaders Display Modules (Caterpillar Monitoring System)
120H and 135H Motor Graders Air System and Brakes Air Tank
554 Forwarder and 574 Forwarder Engine Starting with Jump Start Cables
824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Detent Coil (Control Lever)
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Starting with Auxiliary Start Receptacle - If Equipped
928G Wheel Loader After Starting Engine
966G and 972G Wheel Loaders Excavating with Bucket
938G Wheel Loader and IT38G Integrated Toolcarrier Parking Brake
928G Wheel Loader Secondary Steering
928G Wheel Loader Accelerator Control
966G and 972G Wheel Loaders Logging Fork Clamp
966G and 972G Wheel Loaders Operating Technique Information
966G and 972G Wheel Loaders Bucket Loading from a Stockpile
966G and 972G Wheel Loaders Bucket Loading Hauling Units
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.