Camshaft Position Sensor - Remove and Install
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" M0066576.
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Start By:
a. Remove the electric starting motor.
Show/hide table
| |
| Illustration 1 | g06277056 |
Show/hide table
| |
| Illustration 2 | g06277058 |
Show/hide table
| |
| Illustration 3 | g06277059 |
- Install the camshaft position sensor in the reverse order of removal.
Show/hide table
| |
| Illustration 4 | g06277061 |
Caterpillar Information System:
C7.1 Marine Propulsion Engine Flow Control Valve - Remove and Install
C7.1 Marine Propulsion Engine ECM Mounting Bracket - Remove and Install
G14.2L and G21.9L Gas Engine General Maintenance Information
C32 Tier 4 Final Marine Engines Electronic Unit Injector - Adjust
C32 Tier 4 Final Marine Engines Lubrication System
C32 Tier 4 Final Marine Engines Air Inlet and Exhaust System
C32 Tier 4 Final Marine Engines Fuel System
C32 Tier 4 Final Marine Engines Electronic Control System Components
C32 Tier 4 Final Marine Engines General Information
336 and 336 GC Excavator Operator Controls
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuel Lift Pump Strainer - Replace - If equipped
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Engine Oil and Filter - Change
320 GC, 320 and 323 Excavator Machine Systems Assist - Calibrate - Additional Fine-Tuning for Grade Assist
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Window Washer Reservoir - Fill
A New Duplex Oil Filter Lever Linkage Assembly is Now Used on Certain 3500 Marine Engines {1306, 1308} A New Duplex Oil Filter Lever Linkage Assembly is Now Used on Certain 3500 Marine Engines {1306, 1308}
New Software Is Now Used for Certain 7 Inch and 13 Inch Cat® Marine Displays {7490, 7490} New Software Is Now Used for Certain 7 Inch and 13 Inch Cat® Marine Displays {7490, 7490}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Windows - Clean
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Operator Controls
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuel Tank Cap - Clean
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Battery Disconnect Switch
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Air Cleaner - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Camera - If Equipped
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Monitoring System
SCR Retrofit Aftertreatment Kit Catalyst (SCR) - Remove and Install