Payload System - Configure
Show/hide table
Illustration 1 | g01962688 |
Structure of the "Settings" menu |
The following information describes the settings for the "Settings: Payload Config" menu on the truck. The "Settings: Payload Config" menu is located in the "Settings" menu under "VIMS". Refer to the Systems Operation Section, "Settings Menu" to view the structure of the "Settings" menu.
Note: To configure the settings for the payload, the Advisor must have the Service Mode enabled. Refer to Systems Operation Section, "Service Mode Menu" for instructions to enable the Service Mode.
Show/hide table
Illustration 2 | g01962469 |
"Settings: Payload Config" menu |
- Navigate to the "Payload" menu from the "Settings" menu. Press the "OK" key to continue.
- Press the DOWN button to select the "Payload Target Weight".
- Press the "OK" button to change the value for the "Payload Target Weight".
- Enter the desired value for the "Payload Target Weight" field by pressing the UP arrow or the DOWN arrow to change the value.
- Press the "OK" button to accept the value that is displayed and to return to the parameter configuration selection.
- Navigate to the "Payload" menu from the "Settings" menu. Press the "OK" key to continue.
- Press the DOWN button to select the "Payload Overload Limit".
- Press the "OK" button to change the value for the "Payload Overload Limit".
- Enter the desired value for the "Payload Overload Limit" field by pressing the UP arrow or the DOWN arrow to change the value.
Note: Refer to the Systems Operation Section, "Maximum Payload Speed Manager" for information on selecting a setting for the overload limit.
- Press the "OK" button to accept the value that is displayed and to return to the parameter configuration selection.
- Navigate to the "Payload" menu from the "Settings" menu. Press the "OK" key to continue.
- Press the DOWN button to select the "Payload Last Pass Status".
- Press the "OK" button to change the value for the "Payload Last Pass Status".
- Enter the desired value for the "Payload Last Pass Status" field by pressing the UP arrow or the DOWN arrow.
- Press the "OK" button to accept the value that is displayed and to return to the parameter configuration selection.
Caterpillar Information System:
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Payload System - Calibrate
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Self Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Wiring Harness (Short Circuit) - Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Wiring Harness (Open Circuit) - Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Sensor Supply - Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Sensor Signal (PWM) - Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Electrical Connector - Inspect
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Data Link Configuration Status - Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Data Link - Test
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Reports and Messages Not Available
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Electronic Service Tool Does Not Communicate
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Operating Hours Discrepancy
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Display Module - Replace
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System ECM Software - Install
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System ECM - Replace
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System ECM - Configure
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Router - Configure
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Cable Connections
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Off-Board Service Tool
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Connector Contact Description
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Glossary of Terms
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System System Schematic
C11 and C13 Engines Cylinder Liner
Different Housings are Used on 3400 Remanufactured Engines {1304} Different Housings are Used on 3400 Remanufactured Engines {1304}