Fuel Pressure Is High
Use this procedure to troubleshoot high fuel pressure. Use this procedure if the following event code is active. Refer to Troubleshooting, "Codes" for information about event codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".
Show/hide table
J1939 Code and Description | CDL Code and Description | Comments |
---|---|---|
94-16
Engine Fuel Delivery Pressure : High - moderate severity (2) |
E1218 (2)
High Unfiltered Fuel Pressure |
The fuel pressure before the secondary filter is higher than expected. |
Show/hide table
Associated Diagnostic Trouble Codes | ||
---|---|---|
J1939 Code | CDL Code | Troubleshooting Procedure |
95-0 | E390 (3) | Troubleshooting, "Fuel Filter Is Restricted" |
95-15 | E390 (1) | Troubleshooting, "Fuel Filter Is Restricted" |
95-16 | E390 (2) | Troubleshooting, "Fuel Filter Is Restricted" |
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Check for Codes A. Apply electrical power to the engine. B. Connect Cat® Electronic Technician (ET) to the service tool connector. C. Look for active codes that are associated with the system for the event code. |
Codes |
Result: An associated code is active. Troubleshoot any associated codes before continuing with this test. Result: A code is active or logged. Proceed to Test Step 2. |
Show/hide table
Illustration 1 | g03810811 |
Typical Fuel Filter (1) Starting priority valve (2) System pressure regulator |
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
2. Check the Starting Priority Valve A. Remove electrical power from the engine. B. Remove the starting priority valve from the secondary fuel filter head. Refer to D&A manual for proper procedure. C. Check the starting priority valve operation by actuating the spool within the cartridge assembly. |
Starting Priority Valve |
Result: The starting priority valve moves freely through the full travel. Reinstall the starting priority valve. Proceed to Test Step 3. Result: The starting priority valve does NOT freely move through the full travel. Repair: Replace the starting priority valve. Proceed to Test Step 7. |
3. Check the Low-Pressure Fuel System Pressure Regulator A. Remove electrical power from the engine. B. Remove the low-pressure fuel system pressure regulator from the secondary fuel filter auxiliary manifold. Refer to D&A manual for proper procedure. C. Check the low-pressure fuel system pressure regulator by actuating the spool within the cartridge assembly. |
Low-Pressure Fuel System Pressure Regulator |
Result: The low-pressure fuel system pressure regulator moves freely through the full travel. Reinstall the low-pressure fuel system pressure regulator. Proceed to Test Step 4. Result: The low-pressure fuel system pressure regulator does NOT freely move through the full travel. Repair: Replace the low-pressure fuel system pressure regulator. Proceed to Test Step 7. |
Show/hide table
Illustration 2 | g03812528 |
Secondary Filter Assembly (14) Injector cooling orifice fitting |
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
4. Check the Injector Cooling Supply Orifice A. Remove electrical power from the engine. B. Disconnect the injector cooling supply line from the secondary fuel filter head. C. Remove the orifice from the secondary fuel filter head. Refer to D&A manual for proper procedure. D. Inspect the injector cooling supply orifice. |
Blockage |
Result: The injector cooling supply orifice was NOT blocked. Reinstall the injector cooling supply orifice. Proceed to Test Step 5. Result: The injector cooling supply orifice was blocked. Repair: Clean the blockage from the injector cooling supply orifice. Proceed to Test Step 7. |
Show/hide table
Illustration 3 | g03811112 |
Injector cooling back-pressure regulator (15) Pressure regulator |
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
5. Check the Injector Backpressure Regulator A. Remove electrical power from the engine. B. Remove Injector backpressure regulator from the low-pressure injector cooling manifold in the fuel cooling rail. Refer to D&A manual for proper procedure. C. Check the Injector backpressure regulator by actuating the spool within the cartridge assembly. |
Injector Backpressure Regulator. |
Result: The Injector backpressure regulator moves freely through the full travel. Reinstall the Injector backpressure Regulator. Proceed to Test Step 6. Result: The Injector backpressure Regulator does NOT freely move through the full travel. Repair: Replace the Injector backpressure regulator. Proceed to Test Step 7. |
6. Check the Fuel Cooler A. Remove electrical power from the engine. B. Install a pressure gauge in the inlet and outlet to the fuel cooler. C. Start the engine and operate at high idle. |
Restriction |
Result: The pressure drop across the fuel cooler was less than Proceed to Test Step 7. Result: The pressure drop across the fuel cooler was greater than Repair: Replace the fuel cooler. Proceed to Test Step 7. |
7. Check for Diagnostic Codes A. Start the engine and operate at high idle for 1 minute. B. Look for active or logged diagnostic codes. |
Diagnostic Codes |
Result: No codes present. Return to service. |
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Caterpillar Information System:
C175-16 Locomotive Engine Exhaust Differential Temperature Is High
G3508J, G3516J, and G3520J Engines Aftercooler - Remove and Install
C175-20 Locomotive Engine DEF Tank Level Is Low
XQ570 Rental Generator Set Safety Messages
C175-16 Locomotive Engine Crankcase Pressure Is High
Energy Storage System Fuse - Replace
Energy Storage System Current Sensor - Replace
Energy Storage System Contactor - Replace
Energy Storage System Carbon Dioxide (CO2) Scrubber - Replace
C12.9 Marine Engines Air Cleaner - Remove and Install
Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610} Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610}
C12.9 Marine Engines Turbocharger - Inspect
C1.7 and C2.2 Industrial Engine Speed/Timing - Test
C12.9 Marine Engines Alternator - Remove and Install
C18 Generator Set Maintenance Interval Schedule - Auxiliary
G3512 Generator Set Engines Detonation - Test
G3512 Generator Set Engines Electrical Power Supply - Test
C175-16 Locomotive Engine Fuel Temperature Is High
G3512 Generator Set Engines Exhaust Temperature Is High
G3512 Generator Set Engines Exhaust Temperature Is Low
G3512 Generator Set Engines Fuel Metering Valve - Test - TecJet Valve
C175-16 Locomotive Engine Oil Filter Differential Pressure Problem
Cat® Command For Hauling MID 039 - CID 0839 - FMI 02
C175-16 Locomotive Engine NOx Sensor - Test