Engine Has Mechanical Noise (Knock)
- Active codes and logged codes
- Electrical connections
- Fuel injection
- Fuel quality
- Proper lubrication
- Isolate the source of the noise.
- Valve train components
- Gear train and lower end components
- Crankshaft
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Active Codes and Logged Codes A. Establish communication between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary. B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes. |
Codes |
Result: There are active codes. Repair: Troubleshoot any active codes before continuing with this procedure. Result: There are no active codes. Proceed to Test Step 2. |
2. Electrical Connections A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors. |
Connectors |
Result: There are suspect connectors. Repair: Repair connectors that are suspect or replace connectors that are suspect. Perform the "Wiggle Test" on Cat ET. Result: There are no suspect connectors. Proceed to Test Step 3. |
3. Fuel Injection A. Perform the "Fuel System Verification Test" in the "Diagnostic Tests" under the "Diagnostics" menu. |
Injector Solenoid Test or Fuel System Verification Test |
Result: The test was successful. Proceed to Test Step 4. Result: The test was not successful. Repair: Diagnose the problem and then repair the problem. Reset all active codes and clear all logged codes. Verify that the repair eliminated the problem. |
4. Fuel Quality A. Refer to Operation and Maintenance Manual for information on the proper characteristics of the fuel for the engine. If necessary, obtain a fuel analysis in order to confirm that the correct fuel is being used for the engine. Refer to Systems Operation/Testing and Adjusting, "Fuel System Quality Test" for the proper procedure. |
Fuel |
Result: The fuel quality is OK. Proceed to Test Step 5. Result: The fuel quality is not OK. Repair: Replace the fuel. Verify that the repair eliminated the problem. |
5. Proper Lubrication A. Check for proper lubrication of the valve components. Check for sufficient lubrication between the injector tappets and the rocker arms. B. Check for blocked oil passages. Oil passages must be clean. Clean any oil passages that are questionable. Refer to the Disassembly and Assembly for additional information. C. Inspect the engine oil filters for ferrous material. D. Obtain an S·O·S oil analysis. The analysis will contribute to a better understanding of oil contamination and the origin of the contamination. |
Lubrication |
Result: The oil passages are not blocked and the engine has proper lubrication. Proceed to Test Step 6. Result: The oil passages are blocked or the engine does not have proper lubrication. Repair: Make the necessary repairs, Verify that the repair eliminated the problem. |
6. Isolate the Source of the Noise A. If the source of the noise is the engine accessory, remove the suspect engine accessory. Inspect the suspect engine accessory. |
Engine accessory |
Result An engine accessory is the source of the noise. Repair: Repair the engine accessory and/or replace the engine accessory, if necessary. Result An engine accessory is not the source of the noise. Proceed to Test Step 7. |
7. Valve Train Components A. Check the valve lash. Refer to Troubleshooting, "Valve Lash Is Excessive". B. Check for damage to valve train components. Remove the valve cover from the suspect cylinders. Check the following items for damage: 1. Camshaft 2. Valve rotocoil 3. Valve springs 4. Camshaft followers 5. Rocker shaft 4. Bridges 5. Pushrods 6. Injectors Refer to the Disassembly and Assembly for additional information. C. Check for valves that do not move freely. Remove the cylinder head and inspect the valves. Refer to the Disassembly and Assembly for additional information. |
Valve train |
Result: The valve train components are not damaged. Proceed to Test Step 8. Result: The valve train components are damaged. Repair: Make the necessary repairs, Verify that the repair eliminated the problem. |
8. Gear Train and Components of the Lower End A. Inspect the gear train and lower end components. |
Gear train |
Result: The gear train or lower end components are damaged. Repair: Replace any damaged parts. Result: The gear train or lower end components are not damaged. Proceed to Test Step 9. |
9. Crankshaft A. Inspect the crankshaft and the related components. Look for worn thrust plates and wear on the crankshaft. B. Inspect the connecting rod bearings and the bearing surfaces on the crankshaft. Make sure that the bearings are in the correct position. C. Check the counterweight bolts. |
Crankshaft |
Result: The crankshaft or the related components are damaged or worn. Repair: Repair or replace any damaged parts. Verify that the repair eliminated the problem. |
Caterpillar Information System:
C175-16 PETROLEUM ENGINES Fuel Priming Pump - Remove and Install
CG137-12 Generator Set Maintenance Interval Schedule
XQ400 Power Module Fluid Recommendations
CG137-08 and CG137-12 Engines Refill Capacities
XQ400 Power Module Before Starting Engine
CG137-12 Generator Set Sensors and Electrical Components
XQ400 Power Module Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.4
XQ400 Power Module Alarms and Shutoffs
CG137-08 and CG137-12 Engines Plate Locations and Film Locations
C7 and C9 Industrial Engines Engine Cranks but Does Not Start
C15 and C18 Engines for Caterpillar Built Machines ECM Does Not Communicate with Other Modules
C7 and C9 Industrial Engines Cylinder Is Noisy
C7 and C9 Industrial Engines Air Shutoff - Test
C4.4 Engines Valve Position - Test
C4.4 and C7.1 Engines Water in Fuel - Test
C4.4 Engines for Caterpillar Built Machines Temperature Sensor (Catalyst Inlet) - Remove and Install
C3.4B Engines NOx Sensor - Test
C4.4 Engines for Caterpillar Built Machines Ammonia Sensor - Remove and Install - Ammonia Sensor if Equipped
C4.4 Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Selective Catalytic Reduction (SCR) Temperature Sensor
Cat® Reman Injectors with Invalid Injector Trim Files {1290} Cat® Reman Injectors with Invalid Injector Trim Files {1290}
2014/09/26 A New Special Instruction Is Now Available for Bypassing EGR Relay in EMCP2 Controls on Certain Generator Sets {1908, 4490, 4493}
C175-16 PETROLEUM ENGINES Fuel Transfer Pump - Remove and Install
C3.4B Engines Power Take-Off - Test
C3.4B Engines Relay - Test - ECM Main Relay