Inlet and Exhaust Valve Seat Inserts - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 166-7441 | Valve Seat Extractor Tool | 1 |
B | 1P-0510 | Driver Gp | 1 |
Start By:
- Remove the inlet valves and the exhaust valves.
Note: For information on the reusability of valve seats, refer to Guideline For Reusable Parts And Salvage Operation, SEBF8155.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove valve seat inserts (2) from cylinder head (1).
- Thoroughly clean the valve seat bores in the cylinder head.
Show/hide table
Illustration 1 | g01133493 |
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem projection. An excessive valve stem projection indicates that the valve seat insert is not seated or material was not cleaned from the bottom of the counterbore.
Note: If the valve seats are replaced, you must replace the valve guides.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lower the temperature of valve seat inserts (2).
- Use Tooling (B) to install valve seat inserts (2) in cylinder head (1).
Show/hide table
Illustration 2 | g01133494 |
End By:
- Install the inlet valves and the exhaust valves.
Caterpillar Information System:
C18 Engine Maintenance Interval Schedule
XQC1200 and XQC1600 Power Modules Inlet and Exhaust Valve Guides - Remove and Install
3516C and C175-16 Engines Selective Catalytic Reduction Clean Emissions Module Has High Oxygen Level
XQC1200 and XQC1600 Power Modules Inlet and Exhaust Valves - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet and Exhaust Valve Springs - Remove and Install
3516C and C175-16 Engines Selective Catalytic Reduction SCR Catalyst Temperature Sensor - Test
XQC1200 and XQC1600 Power Modules Cylinder Head - Install
XQC1200 and XQC1600 Power Modules Cylinder Head - Remove
XQC1200 and XQC1600 Power Modules Electronic Unit Injector - Install
Bench Test Procedure for Hydraulic Piston Pumps{0599, 5070, 5070} Bench Test Procedure for Hydraulic Piston Pumps{0599, 5070, 5070}
XQC1200 and XQC1600 Power Modules Electronic Unit Injector - Remove
XQC1200 and XQC1600 Power Modules Water Pump - Assemble
C18 Marine Engine Maintenance Interval Schedule
3516C and C175-16 Engines Selective Catalytic Reduction Manifold DEF Temperature Is High
XQC1200 and XQC1600 Power Modules Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump
2014/07/18 Cat® Reman Announces the Addition of C32 Engines {1000}
3516C and C175-16 Engines Selective Catalytic Reduction Manifold DEF Temperature Is Low
XQC1200 and XQC1600 Power Modules Accessory Drive (Front) - Assemble - Engine Oil Pump and Water Pump
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Sensor - Test
2014/07/25 Water Pump Operation for C7.1 Engines {1361}
C18 Marine Engine Maintenance Interval Schedule
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Temperature Is High
C7.1 Generator Sets Safety Messages
XQC1200 and XQC1600 Power Modules Engine Oil Filter Housing - Remove and Install