Centrifugal Oil Filter - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 185-3630 | Strap Wrench Assembly | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Ensure that all of the rotor components are thoroughly clean before assembling the rotor. Failure to do so can cause an out of balance condition that can cause rapid wear to the bearings and the spindle. |
- Lubricate shuttle (17) with clean engine oil. Place the shuttle and spring (16) in body (12). Install the gasket and plug (14).
Note: Bearing (3) and bearing (15) were checked in the disassembly procedure.
- Install spindle (7) in body (12).
- Position stand tube (8) on base (13).
- Install a new paper liner (5) in rotor cover (4). Place O-ring seal (11) on base (13). Position rotor cover (4) on the base.
- Position the rotor assembly on spindle (7).
- Use Tooling (A) to hold the rotor assembly and install nut (2).
- Install O-ring seal (9) on the body.
- Place cover (6) and clamp (10) on the body. Tighten clamp (10) and nut (1).
Show/hide table
Illustration 1 | g01209308 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
Note: Before you assemble the centrifugal oil filter, thoroughly clean all of the parts and inspect all of the parts. Replace parts that are damaged or worn.
End By:
- Install the centrifugal oil filter.
Caterpillar Information System:
C280-08 Tier 4 Engine Centrifugal Oil Filter - Disassemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Centrifugal Oil Filter - Remove and Install
390F Excavator Machine Systems Check Valve (Counterweight Circuit) - Assemble
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Bucket Open Does Not Respond To Progressive Joystick Motion
C280-08 Tier 4 Engine Engine Oil Filter Housings - Assemble
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Bucket Open Does Not Function
C280-08 Tier 4 Engine Engine Oil Filter Housings - Disassemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Filter Housings - Remove and Install
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Caterpillar Approved Work Tools
390F Excavator Machine Systems Check Valve (Counterweight Circuit) - Disassemble
C280-08 Tier 4 Engine Engine Oil Filter Elements - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Assemble
C4.4 Marine Generator Set Alternator Is Noisy
C4.4 Marine Generator Set Alternator Problem
C4.4 Marine Generator Set Battery Problem
C4.4 Marine Generator Set Coolant Contains Oil
C4.4 Marine Generator Set Coolant Level Is Low
C4.4 Marine Generator Set Coolant Temperature Is High
C4.4 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C4.4 Marine Generator Set Crankcase Breather Ejects Oil
C4.4 Marine Generator Set Crankcase Fumes Disposal Tube Has Oil Draining
374F and 390F Excavators Tool Control System Medium Pressure: Default Value of Work Tool Parameters
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust