Fuel Priming Pump - Remove and Install
- 将燃油供应转到断开位置,并将电源断路开关转到断开位置。
Show/hide table
图 1 g03391985 - 将连接到 ARD 歧管的燃油管(未显示)从两端断开。
- 拆下螺栓 (1)。 断开线束组件 (2)。
Show/hide table
图 2 g02139134 - 将螺栓 (3) 从歧管上拆下。
Show/hide table
图 3 g02139144 - 拆下歧管 (4)。
Show/hide table
图 4 g02138698 - 卸下锁紧螺母 (5)。
Show/hide table
图 5 g02139150 - 记下极性后将导线 (6) 从接线柱上拆下。 接线柱上通过 “+” 和 “-” 号标出了极性。
Show/hide table
图 6 g02139164 - 拆下密封件 (7)。
Show/hide table
图 7 g02139169 - 拆卸泵组件 (8)。
Show/hide table
图 8 g02167735 - 将支承环 (9)、密封 (10) 和密封 (11) 从泵组件上拆下。
- 利用泵套件内提供的泵密封安装工具压入新泵 (12) 和密封。
注: 泵出口应当位于上止点位置。
Show/hide table图 10 g02139286 - 将导线重新安装到接线柱上。 安装新锁紧螺母 (6)。 将锁紧螺母上紧到
1.3 N·m (1 lb ft) 。Show/hide table图 11 g02139307 - 安装新密封 (7)。
Show/hide table
图 12 g02139309 - 重新安装歧管 (4)。
Show/hide table
图 13 g02139311 - 重新安装螺栓 (3)。 将螺栓上紧到
12 ± 3 N·m (9 ± 2 lb ft) 。Show/hide table图 14 g02138801 - 更换滤清器接头 (13)。
Show/hide table
图 15 g03391985 - 安装螺栓 (1)。 重新连接线束组件 (2)。
- 将燃油供应转到 ON 位置,并将电源断路开关转到 ON 位置。
- 由两人冲洗燃油泵和燃油管 (1),并将冲洗液收集到适当的容器中,以便于随后的处理。 可以通过转动钥匙或按下手动开关启动燃油泵。 可能配备的手动开关位于燃油粗滤器底座上。
- 将燃油管 (1) 连接到 ARD 歧管上。
- 重新组装后,通过转动钥匙或按下手动开关为发动机充油。 可能配备的手动开关位于燃油粗滤器底座上。 目视检查泵和 ARD 歧管接头周围有无泄漏。 如果发现泄漏,务必在继续下一步之前解决泄漏问题。
Show/hide table
图 9 | g02139275 |
新燃油充油泵的正确方位。 |
Caterpillar Information System:
Well Service Pumps Machine Operation
3512E Tier 4 Final Engines for Land Electric Drilling Oil Pressure Is Low
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Diagnostic Capabilities
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys DC Bus Capacitor - Replace
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Bearing (3.5 EVD or Greater) - Replace
C13 and C15 Generator Sets Generator Operation
C7.1 Industrial Engine Maintenance Interval Schedule
C4.4 Industrial Engine Welding on Engines with Electronic Controls
C6.6 Industrial Engine After Starting Engine
C4.4 Industrial Engine Cold Weather Starting
C175-16 Locomotive Engine Housing (Front)
3516C HD Petroleum Well Service Engines Customer Specified Parameters Worksheet
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Remove and Install
Procedure to Troubleshoot All Refueling Pump Leaks on Certain Excavators{1295} Procedure to Troubleshoot All Refueling Pump Leaks on Certain Excavators{1295}
C13 and C15 Generator Sets Product Lifting
2013/07/01 New Flywheel Housing Assemblies and Gaskets Are Used on Certain 3500 Locomotives Engines {1157, 7555}
3512C Petroleum Engines with Dynamic Gas Blending Engine Control Switch - Test
C13 and C15 Generator Sets Product Installation
C15 and C18 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
2014/06/20 J1939 Suspect Parameter Numbers for G3300B and CG137 Engines {1900, 1901, 1920}
C15 and C18 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
C13 and C15 Generator Sets Plate Locations and Film Locations
C7.1 Marine Generator Set Starting the Engine