Glow Plugs - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将蓄电池断路开关转到断开位置。
Show/hide table
图 1 g03383021 - 将螺母 (3) 从母线 (2) 上拆下。
- 将导线 (4) 从母线 (2) 上断开。
- 拆下将母线 (2) 固定到电热塞的螺栓 (1)。
- 将母线 (1) 从电热塞上拆下。
Show/hide table
图 2 g03383023 - 清洁电热塞 (5) 周围的区域。 拆卸电热塞之前,确保该区域无污染。
- 从缸盖 (6) 上拆下电热塞 (5)。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 247-5377 | 扭矩扳手 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 安装电热塞 (5) 之前,确保电热塞操作正确。 有关正确的步骤,请参阅故障诊断与排除, "电热塞起动辅助 - 测试"“检查电热塞的操作情况”。
- 确保电热塞的螺纹清洁、无损坏。 更换所有损坏的电热塞。
- 将电热塞 (5) 安装到缸盖 (6) 中。 拧紧电热塞至扭矩为
15 N·m (132 lb in) 。Show/hide table图 4 g03383021 Show/hide table图 5 g03383025 - 将母线 (2) 定位在电热塞上。 将螺母 (1) 安装到电热塞上。
- 使用工具 (A),拧紧螺母 (1) 至扭矩为
2 N·m (17 lb in) 。 - 将导线 (4) 连接到母线 (2) 的螺柱上。
- 将螺母 (3) 安装到母线 (2) 的螺柱上。 拧紧螺母至扭矩为
6 N·m (53 lb in) 。 拧紧螺母 (3) 前,确保导线 (4) 正确定位在 30 度。 - 将蓄电池断路开关转到接通位置。
Show/hide table
图 3 | g03383023 |
Caterpillar Information System:
C7.1 Engines Gear Group (Front) - Remove and Install
C7.1 Engines Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C7.1 Engines Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 Engines Fuel Priming Pump - Remove and Install - Mechanical Priming Pump
C7.1 Engines Fuel Manifold (Rail) - Remove and Install
C7.1 Engines Fuel Injection Pump Gear - Remove
C7.1 Engines Fuel Injection Pump Gear - Install
C7.1 Engines Fuel Injection Pump - Remove
C7.1 Engines Fuel Injection Pump - Install
C7.1 Engines Fuel Injection Lines - Remove
C7.1 Engines Fuel Injection Lines - Install
C7.1 Marine Engine Engine Oil Filter Base - Remove and Install - M.C.S. Duplex Engine Oil Filter Base
C7.1 Engines Housing (Front) - Install - Heavy Duty Housing (Front)
C7.1 Engines Housing (Front) - Install
C7.1 Engines Housing (Front) - Remove - Heavy Duty Housing (Front)
C7.1 Engines Housing (Front) - Remove
C7.1 Engines Idler Gear - Install
C7.1 Engines Idler Gear - Remove
C7.1 Engines Idler Pulley - Remove and Install - Flat Idler Pulley
C7.1 Engines Idler Pulley - Remove and Install - Grooved Idler Pulley
C7.1 Engines Inlet Air Temperature Sensor - Remove and Install
C7.1 Engines Inlet and Exhaust Valve Springs - Remove and Install
C7.1 Engines Inlet and Exhaust Valves - Remove and Install
C7.1 Engines Inlet Manifold - Remove and Install