Cylinder Block
Show/hide table
| |
| Illustration 1 | g03335132 |
|
Front view | |
Show/hide table
| Specification for 383-7230 Cylinder Block Gp | |||
| Item | Qty | Part | Specification Description |
| The top face of the cylinder block, bottom surface of spacer plate and both sides of plate gasket must be free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants during assembly. | |||
| 1 | 8 | 197-7008 Dowel | Extension of the dowel is |
| 2 | 16 | 8T-0099 Dowel | Extension of the dowel is |
| - | - | - | Thickness of the spacer plate is |
| 3 | 8 | 6V-3348 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
| 4 | 5 | 223-1696 Crankshaft Bearing Cap | Install crankshaft bearing caps with the part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail.
Width in the cylinder block for crankshaft bearing cap is |
| A | 10 | 116-1359 Camshaft Bearing | The camshaft bearing joint must be on the horizontal centerline of the bore. |
| Oil holes must be positioned from horizontal at an angle (B) of 20.0 ± 0.5 degrees as shown in Illustration 1. | |||
| After installation, bore is |
|||
| C | - | - | New dimension from centerline of crankshaft bearing bore to the top of the block is |
| D | - | - | Width of the crankshaft bearing cap is |
| E | - | - | New dimension from centerline of crankshaft bearing bore to bottom of block (pan rails) is |
| F | - | - | Bore in the block for the crankshaft bearings is |
Show/hide table
| |
| Illustration 2 | g03335133 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 5 | 2 | 4W-4813 Plug | Torque to |
| 6 | 8 | 352-6061 Liner Seal | Assemble dry seals on clean and dry liner grooves. |
| Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. | |||
| 7 | 24 | 7N-2046 O-Ring Seal | Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| 8 | 20 | 7X-7925 Bolt | Use the following procedure in order to tighten the crankshaft bearing cap bolts.
1. Before assembly, Lubricate the threads with clean engine oil . 2. Tighten the bolts by hand. 3. Tighten the bolts in the numerical sequence as shown in Illustration 2 to 4. Again tighten the bolts to an additional angle of 180 ± 5 degrees |
Show/hide table
| |
| Illustration 3 | g03335134 |
|
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 9 | 1 | 4W-4814 Adapter | Torque to |
| 10 | 4 | 5F-9657 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
| G | 3 | 7N-2047 Dowel | Extension of the dowel is |
| H | 2 | 4N-0683 Dowel | Extension of the dowel is |
| J | 2 | 7N-2044 Dowel | Extension of the dowel is |
Caterpillar Information System:
3500C Marine Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
3500 Engines for Caterpillar Built Generator Sets Radiator
3500 Engines for Caterpillar Built Generator Sets Crankcase Breather
3500 Engines for Caterpillar Built Generator Sets Crankcase Breather
3500C Marine Engines Gear Group (Front) - Reverse Rotation
C7.1 Industrial Engine Engine Electronics
3500 Engines Flywheel Housing Cover
3500C Marine Engines Gear Group (Front) - Reverse Rotation
3500C Marine Engines Gear Group (Rear)
C1.5 and C2.2 Industrial Engines ARD Nozzle - Test
3500C Marine Engines Gear Group (Rear)
3500 Engines for Caterpillar Built Generator Sets Fan Drive
390F Excavator Plate Locations and Film Locations
3500C Marine Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
3500 Engines for Caterpillar Built Generator Sets Accessory Drive (Upper Right Hand)
3512B and 3516B Engines Engine Oil Cooler - Install
3500C Marine Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
3500 Engines for Caterpillar Built Generator Sets Tachometer Drive
3500C Marine Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
2012/12/20 Correct Turbocharger Hose Clamp Location for 345C, 345D, and 349D Excavators and Mobile Hydraulic Power Units {1052, 1071, 7553}
3512B and 3516B Engines Inlet and Exhaust Valves - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Diesel Particulate Filter Temperature Is High
C18 Industrial Engine Intake Manifold Air Temperature Is High
Failures on the 256-5984 Rotocoil As Installed in C175 Engines{1100, 1109} Failures on the 256-5984 Rotocoil As Installed in C175 Engines{1100, 1109}