Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
拆卸步骤
- 将曲轴箱呼吸器的塑料管组件 (1) 从气门机构盖上断开。
Show/hide table
图 1 | g02168393 |
- 将锁片滑入解锁位置。 将发动机导线线束组件 (5) 从导线线束组件 (6) 上断开。 将导线线束组件 (6) 的接头从支架 (7) 上滑下。
- 切断电缆扎带 (2) 。
- 将温度传感器 (4) 从氮氧化物还原系统 (NRS) 进气控制 (3) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | Bostik 纯镍 防粘结剂     |
1     |
Show/hide table
注意 |
---|
确保导线线束布线正确,且电缆带未过分拧紧。 过分拧紧电缆带会损坏导线线束卷。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 使用工具 (A) 轻轻润滑温度传感器 (4) 的螺纹。 将温度传感器 (4) 连接到 NRS 进气控制 (3) 。
Show/hide table
图 2 | g02168393 |
- 拧紧温度传感器 (4) 至扭矩为 24 N·m (212 lb in)。
- 将导线线束组件 (6) 的接头滑到支架 (7) 上。 将发动机导线线束组件 (5) 连接到导线线束组件 (6) 上。 将锁片滑入锁定位置。
- 将新电缆带 (2) 安装到线束组件 (6) 上。
注: 确保电缆带符合原始设备制造商(OEM)的技术规格。
- 将曲轴箱呼吸器的塑料管组件 (1) 连接到气门机构盖上。
Caterpillar Information System:
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Coolant Temperature Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
C7.1 Industrial Engine Boost Pressure Sensor - Remove and Install
C7.1 Industrial Engine Inlet Manifold Temperature Sensor - Remove and Install
C7.1 Industrial Engine Glow Plugs - Remove and Install
C7.1 Industrial Engine Alternator Belt - Remove and Install
C7.1 Industrial Engine Idler Pulley - Remove and Install - Grooved Idler Pulley
C7.1 Industrial Engine Idler Pulley - Remove and Install - Flat Idler Pulley
C7.1 Industrial Engine Belt Tensioner - Remove and Install
C7.1 Industrial Engine Fan - Remove and Install
C7.1 Industrial Engine Fan Drive - Remove and Install
C18 Marine Auxiliary and Marine Generator Set Engines Inlet Air Temperature Is High
C32 Marine Generator Set Fumes Disposal Filter Element - Replace