Coolant Temperature Sensor - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检查, 保养, 测试, 调整 和 维修发动机时,务必留心,确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将冷却液从冷却系统中排出,直到液位在冷却液温度传感器以下。 有关正确的排放步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 将锁片 (2) 滑入解锁位置。 将线束组件 (3) 从冷却液温度传感器 (1) 上断开。
Show/hide table
图 1 | g02315373 |
- 用深孔套筒将冷却液温度传感器 (1) 从缸盖上拆下。
- 将 O 形密封圈 (4) 从冷却液温度传感器 (1) 上拆下。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将一个新 O 形密封圈 (4) 安装到冷却液温度传感器 (1) 上。
注: 不要润滑 O 形密封圈。
Show/hide table
图 2 | g02315373 |
- 用深孔套筒将冷却液温度传感器 (1) 安装到缸盖上。 将冷却液温度传感器拧紧至扭矩为 20 N·m (177 lb in)。
- 将线束组件 (3) 连接到冷却液温度传感器 (1) 上。 将锁片 (2) 滑动到锁定位置。
- 加注冷却系统至正确液位。 有关正确的加注步骤,请参阅操作和保养手册, "冷却系统冷却液液位 - 检查"和操作和保养手册, "冷却系统冷却液 - 测试 / 添加"。
Caterpillar Information System:
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
C7.1 Industrial Engine Boost Pressure Sensor - Remove and Install
C7.1 Industrial Engine Inlet Manifold Temperature Sensor - Remove and Install
C7.1 Industrial Engine Glow Plugs - Remove and Install
C7.1 Industrial Engine Alternator Belt - Remove and Install
C7.1 Industrial Engine Idler Pulley - Remove and Install - Grooved Idler Pulley
C7.1 Industrial Engine Idler Pulley - Remove and Install - Flat Idler Pulley
C7.1 Industrial Engine Belt Tensioner - Remove and Install