Soot Antenna - Remove and Install
拆卸步骤
- 将线束组件 (2) 从烟尘天线 (1) 上断开。
Show/hide table
图 1 | g03383034 |
典型示例 |
- 重复步骤 1 将其余线束组件从其余烟尘天线上断开。
- 使用适当的工具将烟尘天线 (1) 从清洁排放模块 (CEM) 组件 (3) 上拆下。
注: 确保烟尘天线感应元件没有损坏。
- 重复步骤 3 拆下其余烟尘天线。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | Bostik 纯镍 防粘结剂     |
1     |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 使用工具 (A) 轻轻润滑烟尘天线 (1) 的螺纹。
Show/hide table
图 2 | g03383034 |
典型示例 |
- 使用适当的工具将烟尘天线 (1) 安装到 CEM (3) 上。 拧紧烟尘天线至扭矩为 45 N·m (33 lb ft)。
注: 确保烟尘天线感应元件没有损坏。
- 重复步骤 2 安装其余烟尘天线。
- 将线束组件 (2) 连接到烟尘天线 (1) 上。 拧紧线束组件至扭矩为 1.2 N·m (11 lb in)。
- 重复步骤 5,连接其余线束组件。
Caterpillar Information System:
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Coolant Temperature Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
C7.1 Industrial Engine Boost Pressure Sensor - Remove and Install
C7.1 Industrial Engine Inlet Manifold Temperature Sensor - Remove and Install
C7.1 Industrial Engine Glow Plugs - Remove and Install
C7.1 Industrial Engine Alternator Belt - Remove and Install
C7.1 Industrial Engine Idler Pulley - Remove and Install - Grooved Idler Pulley
C7.1 Industrial Engine Idler Pulley - Remove and Install - Flat Idler Pulley
C7.1 Industrial Engine Belt Tensioner - Remove and Install
C7.1 Industrial Engine Fan - Remove and Install
C7.1 Industrial Engine Fan Drive - Remove and Install
C18 Marine Auxiliary and Marine Generator Set Engines Inlet Air Temperature Is High