C9.3 Tier 4 Final Engines Caterpillar

Fuel Injection Pump

Usage:

D6T 2B3

Show/hide table




Illustration 1	g03130476

Show/hide table

Table 1
Specification for 379-0150 Fuel Injection Pump Gp
Item	Qty	Part	Specification Description
1	2	143-9392 Stud	Use the following procedure in order to tightening the studs and the bolts as shown in the Illustration 1:
2	4	5P-8347 Bolt	1. Tighten to 19 ± 1 N·m (168 ± 95 lb in).
			2. Again, turn to reach the final turn angle of 30 ± 1 degrees.
			3. Final tightening torque should be 30 to 40 N·m (22 to 30 lb ft).
3	1	9S-8004 O-Ring Plug	Torque to 35 ± 4 N·m (26 ± 3 lb ft).
4	1	9S-8005 O-Ring Plug	Torque to 70 ± 5 N·m (52 ± 4 lb ft).
5	1	9S-8003 Plug	Torque to 20 ± 2 N·m (177 ± 18 lb in).
6	1	143-9392 Stud	Torque to 30 ± 4 N·m (266 ± 35 lb in).
7	2	6V-5135 Socket Setscrew	Torque to 25 ± 2 N·m (221 ± 18 lb in).
8	1	9S-4180 Plug	Torque to 4.5 ± 0.5 N·m (39.8 ± 4.4 lb in).
9	1	104-6385 Stud	Torque to 30 ± 4 N·m (266 ± 35 lb in).
10	2	6V-3940 Bolt	Torque to 30 ± 4 N·m (266 ± 35 lb in).
11	1	294-3031 Special Bolt	Torque to 9 ± 1 N·m (80 ± 9 lb in).
12	3	8C-8545 Bolt	Torque to 7.0 ± 0.4 N·m (62.0 ± 3.5 lb in).
13	1	6V-5845 Bolt	Before assembly, apply red Loctite 271 to the threads.
			1. Tighten to 200 ± 5 N·m (148 ± 4 lb ft) and rotate to 180 degrees counter clock wise.
			2. Again tighten to 200 ± 5 N·m (148 ± 4 lb ft).
			3. Turn to reach the final turn angle of 31 ± 2 degrees.
			4. And final tightening torque should be 500 ± 50 N·m (369 ± 37 lb ft).

Caterpillar Information System:

CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Replace

CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Configure

CX48-P2300 Petroleum Transmission Power Train Electronic Control System Symptom Troubleshooting

2012/07/19 Improved Flame Arrestors Are Used for Certain G3500E Engines {1071, 1092}

CEM Locomotive Aftertreatment Catalyst (DOC) - Replace

CX48-P2300 Petroleum Transmission Power Train Electronic Control System Cat Data Link - Test

G3500 Engines Cylinder Head

C13 Tier 4 Final Engines Solenoid Valve

2012/10/04 A New Rocker Arm Assembly Is Used in Certain C11 and C13 Commercial Engines {1123}

Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254} Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}

UPS 250 and UPS 300 Uninterruptible Power Supplies Using Computer Software

C32 Marine Engines Turbocharger - Inspect

G3500 Engines Cylinder Head

G3500 Engines Cylinder Head

C7.1 Industrial Engine Fuel Filter (In-Line) - Replace

793F Off-Highway Truck Engine Supplement Turbocharger - Remove and Install - High Altitude

C32 Marine Engines Unit Injector Sleeve - Remove

C32 Marine Engines Unit Injector Sleeve - Install

G3500 Engines Cylinder Head

C7.1 Industrial Engine Maintenance Interval Schedule

C9.3 Industrial Engine Turbocharger

C6.6 Industrial Engine Engine Crankcase Breather Element - Replace

C4.4 Industrial Engine Fuel System Primary Filter (Water Separator) Element - Replace

C4.4 Industrial Engine Fuel System Primary Filter/Water Separator - Drain