Fuel System Secondary Filter - Replace
Show/hide table
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害,当更换燃油滤清器或油水分离器滤芯时,要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
注: 请参阅测试和调整手册, "燃油系统零部件的清洁度"中关于必须在全部燃油系统工作过程中遵循的清洁度标准的详细资料。
Show/hide table
注意 |
---|
确保在进行任何维护和修理工作之前关闭发动机。 |
Show/hide table
注意 |
---|
不要让脏物进入燃油系统。 彻底清洁将要拆开的燃油系统部件的周围区域。 在拆开的燃油系统部件上安放适当的盖。 |
任何时候如果发生了以下情况,请更换燃油细滤器滤芯:
- 压差表记录
103 kPa (15 psi) 。 - 燃油滤清器已经使用了1200个工时数。
Show/hide table
图 1 | g01948301 |
Show/hide table
注意 |
---|
使用适当的容器来盛接可能溅出的燃油。 立即清理所有溅溢的燃油。 |
- 拆下旧滤清器。
- 在新的燃油滤清器密封垫上涂抹干净的柴油。
Show/hide table
注意 安装燃油滤清器之前不要向燃油滤清器中注入燃油。 否则燃油不会被过滤并可能受污染。 污染的燃油会加速燃油系统零件的磨损。
- 把新燃油滤清器旋装到燃油滤清器底座上,直到密封垫接触到底座。 用手拧紧燃油滤清器一整圈。 不要过分拧紧滤清器。 使用滤清器上的旋转刻度标记作为适当拧紧的指示。
注: 您的产品可能有一个附加的细滤器。 遵照以上步骤更换附加的细滤器。
Caterpillar Information System:
C175-16 Engine Cooling System Water Temperature Regulator - Replace
2012/09/03 A New Oil Filter Base Is Used On Certain Machine Engines {1306, 1308}
C280-12 and C280–16 Marine Engines Turbocharger - Remove
C18 Marine Engine Model View Illustrations
2012/09/05 A New Oil Filter Base is Now Available for Certain Machine Engines {1306, 1308}
3516C Generator Set Engines Flexible Coupling
C18 Marine Engine Model View Illustrations
3516C Generator Set Engines Flexible Coupling
C7.1 Industrial Engine Belt Tensioner - Check
C175-16 Locomotive Engines Engine Oil and Filter - Change
3500C Marine Engines Engine Oil Filter
C7.1 Industrial Engine Belt - Inspect
C175-16 Engine Fuel System Primary Filter/Water Separator - Clean/Replace
C18 Engine Product Description
2012/06/15 New Software Is Used On Certain Tier 3 C18 Industrial Engines {1901, 1920}
G3500 Engines Prelube Pump
G3500 Engines Prelube Pump - Air
3516C Generator Set Engines Engine Oil Lines
C7.1 Industrial Engine Coolant (DEAC) - Change
3516C Generator Set Engines Fuel Injection Lines
3516C Generator Set Engines Electronic Unit Injector Wiring
3516C Generator Set Engines Diesel Exhaust Fluid Tank
3516C Generator Set Engines Diesel Exhaust Fluid Tank
3516C Generator Set Engines Fuel Injection Pump