Gas Pressure Regulator Solenoid - Assemble
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Solder wires (7) in position on adapter (5). Install coil (6) in the housing.
Show/hide table
Illustration 2 g00765416 - Put adapter (5) in position and install screws (4).
- Install washer (3) and spring (2).
Show/hide table
Illustration 3 g00765415 Show/hide tablePersonal injury can result from parts and/or covers under spring pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
- Install cap (1) on the solenoid.
Show/hide table
Illustration 1 | g00765417 |
End By:
- Install the gas pressure regulator solenoid. Refer to Disassembly and Assembly, "Gas Pressure Regulator Solenoid - Install".
Caterpillar Information System:
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Assemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Disassemble
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Inspect/Test - Gauges and Indicators for the Engine
2012/03/21 Set the Overspeed Shutdown for C175-16 Petroleum Engines to 115 Percent of Rated Speed {1900, 1907, 1912, 7427}
Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562} Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562}
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Control Panels for the Pumper
CX48-P2300 Petroleum Transmission Transmission Planetary - Assemble
2012/09/26 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1059, 1067}
SPF343 and SPF343C Trailer Mounted Pumpers Driven Equipment - Check
Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901} Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901}
336E Excavator Machine System Specifications Final Drive and Motor Fastener (Mounting)
3512C and 3516C Marine Engines Piston and Rings
C175-16 Marine Engines Air Inlet and Exhaust System Operation
C175-16 Marine Engines Aftercooler
G3516 Petroleum Engines Gas Pressure Regulator Solenoid - Disassemble
C175-16 Marine Engines Turbocharger
Low Oil Pressure Shutdowns upon Cold Start-Ups for C175 Engines {0645, 1000} Low Oil Pressure Shutdowns upon Cold Start-Ups for C175 Engines {0645, 1000}
C175-16 Marine Engines Lubrication System Operation
C175-16 Marine Engines Cooling System Operation
Operation and Maintenance of 278-1150 Stud Tensioner Tooling Group - Used on C175 Engines{0599, 0701, 0705, 1201, 1202, 1203, 7551} Operation and Maintenance of 278-1150 Stud Tensioner Tooling Group - Used on C175 Engines{0599, 0701, 0705, 1201, 1202, 1203, 7551}
2012/03/26 An Improved Air Inlet Elbow Is Used for a Certain 3516B Marine Engine {1078}
3512C and 3516C Marine Auxiliary Engines Injector Solenoid - Test
C175-16 Marine Engines Finding the Top Center Position for the No. 1 Piston
SPF343 and SPF343C Trailer Mounted Pumpers Safety Messages - Type 2 Safety Messages