Aftercooler - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 1 |
B | - | Guide Stud3/8 - 16 by 4 inch | 2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (A) and attach a suitable lifting device on housing (9).
- Remove all gasket and foreign material from the housing.
Show/hide table
Illustration 2 g00772045 Show/hide tableIllustration 3 g00772213 - Position core (11).
- Put housing (9) and gasket (13) in position on the mounting plate. The two bolt (12) in mounting plate (10) must be installed. Install Tooling (B) in aftercooler (5).
- Install bolts (1) and remove Tooling (B).
- Repeat this procedure for the housing on the opposite side of the aftercooler.
Show/hide table
Illustration 4 g00772041 - Put brackets (6) and (7) in position and install bolts (8).
Show/hide table
Illustration 5 g00772040 - Clean the gasket material from aftercooler (5).
Show/hide table
Illustration 6 g00772036 - Put a new gasket and bonnet (2) in position and install clips (3) and bolts (4) and (1).
- Repeat this procedure for the bonnet on the opposite side of the aftercooler.
Show/hide table
Illustration 1 | g00772208 |
End By:
- Install the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Install".
Caterpillar Information System:
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Disassemble
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Inspect/Test - Gauges and Indicators for the Engine
2012/03/21 Set the Overspeed Shutdown for C175-16 Petroleum Engines to 115 Percent of Rated Speed {1900, 1907, 1912, 7427}
Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562} Thermal Spray Procedures for Hydraulic Cylinder Rods{0679, 7562, 7562}
SPF343 and SPF343C Trailer Mounted Pumpers Control Panel - Control Panels for the Pumper
CX48-P2300 Petroleum Transmission Transmission Planetary - Assemble
2012/09/26 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1059, 1067}
SPF343 and SPF343C Trailer Mounted Pumpers Driven Equipment - Check
Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901} Instruction for Installing 3E-8866 Wire As to Fit Alternate Harness Lengths{1408, 1900, 1901}
336E Excavator Machine System Specifications Final Drive and Motor Fastener (Mounting)
3512C and 3516C Marine Engines Piston and Rings
3512C and 3516C Marine Engines Piston and Rings
G3516 Petroleum Engines Gas Pressure Regulator Solenoid - Assemble
C175-16 Marine Engines Air Inlet and Exhaust System Operation
C175-16 Marine Engines Aftercooler
G3516 Petroleum Engines Gas Pressure Regulator Solenoid - Disassemble
C175-16 Marine Engines Turbocharger
Low Oil Pressure Shutdowns upon Cold Start-Ups for C175 Engines {0645, 1000} Low Oil Pressure Shutdowns upon Cold Start-Ups for C175 Engines {0645, 1000}
C175-16 Marine Engines Lubrication System Operation
C175-16 Marine Engines Cooling System Operation
Operation and Maintenance of 278-1150 Stud Tensioner Tooling Group - Used on C175 Engines{0599, 0701, 0705, 1201, 1202, 1203, 7551} Operation and Maintenance of 278-1150 Stud Tensioner Tooling Group - Used on C175 Engines{0599, 0701, 0705, 1201, 1202, 1203, 7551}
2012/03/26 An Improved Air Inlet Elbow Is Used for a Certain 3516B Marine Engine {1078}
3512C and 3516C Marine Auxiliary Engines Injector Solenoid - Test
C175-16 Marine Engines Finding the Top Center Position for the No. 1 Piston