Engine Monitoring System
电子控制模块(ECM)为该发动机提供了一个综合、可编程的发动机监控系统。 ECM 监控指定的发动机操作参数,以检测可能会发生的异常情况。 如果特定发动机参数超过发动机监控系统所定义的可接受范围,则 ECM 将产生事件代码。 ECM 将会根据该情况的严重程度做出反应。 有关事件代码的信息,请参阅故障诊断与排除, "事件代码"。
以下行动可能由 ECM 触发。 这些行动取决于情况的严重程度。
- 点亮警告灯或警告报警
- 发动机减额
- 发动机停机
每个参数可能会具有以下三种响应。 有些响应对某些参数是无效的。 参考表 1。
Show/hide table
指示灯(1)、(2)和(3)     | |
---|---|
警告类别指示灯     | 严重程度     |
(1)     | 最低严重程度     |
(2)     | 中等严重程度     |
(3)     | 最高严重程度     |
使用 Caterpillar 电子技师(ET)执行监控系统的以下工作:
- 查看参数
- 参数编程
- 设置延迟时间
参数的默认设置已在出厂时进行了编程。 为了适应特定的用途和场所,可以使用 Cat ET 对某些参数重新编程。 利用 Cat ET 修改监控系统参数。
注: 某些参数不需要密码便可修改。 有些参数的更改需要客户密码。 有些参数受出厂密码的保护。 某些参数不能修改。 有些应用不允许对可编程监控系统进行任何更改。 受到出厂密码保护的参数只能由代理商的工作人员进行更改。
查看或更改监控系统的设置
使用以下步骤来查看参数设置和/或更改参数设置:
- 在 Cat ET 上选择 "Service/Monitoring System(维修/监控系统)"屏幕。
- 高亮显示所需参数。 然后点击屏幕左下角的 "Change"(更改)按钮。
此时会出现 "Change Monitor System(更改监控系统)"屏幕。
注: 在继续进行操作前,请确保为要更改的参数选择了正确的 ECM。
- 更改参数的 "State(状态)"。
- 按照屏幕下半部分显示的 "Allowed Values(容许值)"设置 "Trip Point(触发点)"和 "Delay Time(延迟时间)"。
- 点击 "OK(确认)"按钮。
如果需要密码,会出现 "Enter Passwords(输入密码)"屏幕。 输入正确的密码,然后点击 "OK(确定)"按钮。
注: 如果需要出厂密码,会出现 "Enter Factory Passwords(输入出厂密码)"屏幕。 有关获得出厂密码的信息,请参考故障诊断与排除, "出厂密码"。
新的设置会立即生效。
注: 出厂密码仅供来自授权的 Caterpillar 代理商的维修技师使用。 Caterpillar 的客户无权访问 Caterpillar 工厂密码系统(FPS)。
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Diesel Particulate Filter Regeneration
C13, C15, and C18 Tier 4 Final Engines Component Location
C13, C15, and C18 Tier 4 Final Engines System Overview
3516B Generator Set Engines with Dynamic Gas Blending Service Information Report
C13, C15, and C18 Tier 4 Final Engines Electronic Service Tools
C13, C15, and C18 Tier 4 Final Engines Welding Precaution
C13, C15, and C18 Tier 4 Final Engines General Information
C175-16 Marine Propulsion Engines Direct Fuel Control Mode - Test
G3600 Engines Fuel Control
3500C Marine Engines Product Description
2012/02/27 In-line Fuel Strainer on C7.1, C6.6, and C4.4 Engines {1256, 1261}
3516C Industrial Engine Engine Oil Level - Check
C13, C15, and C18 Tier 4 Final Engines Diagnostic Capabilities
C175-16 Marine Engine Pistons and Connecting Rods
2012/02/10 Improved Fuel Priming Pump Groups and Fuel Pump Groups Are Used on Certain Tier 4 Interim Industrial Engines {1256, 1258}
C13, C15, and C18 Tier 4 Final Engines Electrical Connectors
C13, C15, and C18 Tier 4 Final Engines Configuration Parameters
C13, C15, and C18 Tier 4 Final Engines Diagnostic Trouble Codes
C13, C15, and C18 Tier 4 Final Engines Acceleration Is Poor or Throttle Response Is Poor
C13, C15, and C18 Tier 4 Final Engines Alternator Problem - Charging Problem and/or Noisy Operation
C175-16 Marine Engine Pistons, Liners, and Connecting Rods
3512C and 3516C Marine Propulsion Engines Component Location
C175-16 Marine Engine Crankshaft Main Bearings
2012/02/07 Cylinder Head Blanking Plug on Certain C3.4 Engines {1100}