Engine Oil Filter Base - Remove and Install - G3412B
拆卸步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 2P-8250 | 卷带式扳手 | 1 |
| B | - | LOCTITE 271 | 1 |
- 有关正确的排放和加注步骤，请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
- 将线束组件 (1) 从压力传感器 (2) 上断开。 移开线束组件。
Show/hide table
 | |
| 图 1 | g02693976 |
- 拆下压力传感器 (2) 。
- 将防尘盖从气门 (5) 上拆下。
Show/hide table
 | |
| 图 2 | g02694036 |
- 使用工具 (A) 拆下机油滤清器 (6) 。
- 拆下弯头 (3) 。 拆下管组件 (4) 和 O 形密封圈。
- 卸下螺栓 (7) 和螺母 (8) 。
Show/hide table
 | |
| 图 3 | g02694078 |
- 拆下滤清器底座 (9) 和 (10) 。 丢弃密封垫。
- 将空心螺柱 (17) 从滤清器底座 (9) 和 (10) 上拆下。
Show/hide table
 | |
| 图 4 | g02694100 |
- 将螺栓 (11) 、垫圈 (13) 和盖 (13) 从滤清器底座 (9) 上拆下。 拆下弹簧 (15) ，然后拆下气门柱塞 (16) 。
Show/hide table
 |
被弹簧力爆出的零件击中，会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序，并使用所有建议的工具以释放弹簧力。 |
安装步骤
- 按与拆卸相反的顺序安装滤清器底座 (9) 和 (10) 。
- 将工具 (B) 涂覆到空心螺柱 (17) 的螺纹上。 拧紧扭矩至 80 ± 14 N·m (59 ± 10 lb ft)。
- 安装新密封垫 (14) 。 安装滤清器底座 (9) 和 (10) 的新密封垫。
- 用清洁的发动机机油润滑机油滤清器 (6) 的所有密封圈。
- 机油滤清器 (6) 座合在底座上后，多转一整圈。
- 用清洁的发动机机油润滑压力传感器 (2) 的孔。 拧紧至扭矩为 10 ± 2 N·m (89 ± 18 lb in)。
Caterpillar Information System:
2011/09/23 A New Exhaust Cross-Over Bellows Is Used On Certain 3508B and 3508C Engines {1059}
C175-16 Engine for Off-Highway Trucks Temperature Sensor (DEF Cabinet Air)
120 Motor Graders Centershift Cylinder Mounting
2011/08/17 Replacement of the Oil Level Sensor is a Potential Repair Option for an Incorrect Diagnostic Code on Certain CX Transmissions {3133, 3206}
C13, C15, and C18 Tier 4 Final Engines Flywheel Housing
CG137-08 and CG137-12 Industrial Engines Starting - Test
CG137-08 and CG137-12 Engines Engine Oil Cooler - Remove and Install - G3408B
C15 and C18 Industrial Engines Engine Oil Pan - Remove and Install - C18 Engine
CG137-08 and CG137-12 Industrial Engines Cooling System
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Parking
C13, C15, and C18 Tier 4 Final Engines Flywheel
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
CG137-08 and CG137-12 Engines Engine Oil Pan - Remove and Install - G3412B
C15 Engines for Combat and Tactical Vehicles Electronic Control System Components
Photo Request Instructions for Identifying and Repairing 50MT Starter Motor Problems{1453} Photo Request Instructions for Identifying and Repairing 50MT Starter Motor Problems{1453}
C9.3 Engines for Caterpillar Built Machines Fuel Pressure Sensor
C9.3 Tier 4 Final Engines Engine Oil Pressure Sensor
C9.3 Engines for Caterpillar Built Machines Boost Pressure Sensor
C9.3 Tier 4 Final Engines Inlet Air Temperature Sensor
3516C Generator Set Engines Temperature Sensor (Exhaust)
3516C Generator Set Engines Nozzle (DEF)
C280 Marine Engines Nitrogen Oxide Sensor (Engine Exhaust Out)
C280 Marine Engines Nitrogen Oxide Sensor (Exhaust Pipe Out)
CG137-08 and CG137-12 Generator Sets Valve Cover