3516C Generator Set Engines Caterpillar

Gear Group (Rear)

Usage:

3516C LY6

Show/hide table




Illustration 1	g02645180

Show/hide table




Illustration 2	g02645276

Show/hide table

Table 1
Specification for 375-3640 Rear Gear Gp
Item	Qty	Part	Specification Description
1	1	175-5201 Camshaft Gear	Before assembly, clean the taper of the camshaft and the tapered bore of the camshaft drive gear with lint free cloth saturated with cleaning solvent to remove excess oil. Clean with alcohol wipe.
2	2	9X-8887 Bolt	Use the following procedure to tighten the bolt for the camshaft drive gears: 1. Tighten the bolt for the camshaft drive gear to 360 ± 40 N·m (266 ± 30 lb ft). 2. Mark a vertical line on the head of the bolt for the camshaft drive gear. Refer to Illustration 2. 3. Place a driver against the retaining plate of the camshaft drive gear. Strike the driver solidly with a hammer 3 to 4 times. 4. Again, tighten the bolt for the camshaft drive gear to 360 ± 40 N·m (266 ± 30 lb ft). 5. Repeat steps 3 and 4 until the mark on the bolt turns a minimum of 90 degrees. Refer to Illustration 2.
3	4	1B-4367 Bolt	Torque to 240 ± 40 N·m (177 ± 30 lb ft).
4	1	175-5202 Camshaft Gear	Before assembly, clean the taper of the camshaft and the tapered bore of the camshaft drive gear with lint free cloth saturated with cleaning solvent to remove excess oil. Clean with alcohol wipe.
5	2	8S-2331 Bolt	Torque to 240 ± 40 N·m (177 ± 30 lb ft).
6	2	175-5197 Idler Gear As	Bore of 125-9751 Bushing is 81.060 ± 0.010 mm (3.1913 ± 0.0004 inch).
6	2	175-5197 Idler Gear As	Installation depth is 1.00 ± 0.25 mm (0.039 ± 0.010 inch).
7	1	175-5200 Idler Gear As	Bore of 101-1372 Bushing is 75.060 ± 0.010 mm (2.9551 ± 0.0004 inch).
7	1	175-5200 Idler Gear As	Installation depth is 1.5 ± 0.5 mm (0.06 ± 0.02 inch).
8	2	101-1367 Idler Shaft	Diameter is 81.000 ± 0.010 mm (3.1890 ± 0.0004 inch).
9	1	101-1366 Gear Shaft	Diameter is 74.990 ± 0.010 mm (2.9524 ± 0.0004 inch).
10	2	101-1368 Thrust Washer	Thickness is 1.90 ± 0.10 mm (0.075 ± 0.004 inch).
11	4	8M-2530 Bolt	Torque to 140 ± 10 N·m (103 ± 7 lb ft).

Caterpillar Information System:

345B Series II Excavator Machine System Specifications Bucket Cylinder

3500B Engines Engine Mount

C11, C13, and C15 On-highway Engines Maintenance Interval Schedule - C11 and C13 Engines with 500 HP Field Up-Rates and 525 HP RV Ratings with Optional (Shallow) Oil Sumps

C11, C13, and C15 On-highway Engines Maintenance Interval Schedule - C11 and C13 Engines with 500 HP Field Up-Rates and 525 HP RV Ratings with Standard (Deep) Oil Sumps

C11, C13, and C15 On-highway Engines Maintenance Interval Schedule - C11 and C13 Engines with Optional Shallow Oil Sumps

C11, C13, and C15 On-highway Engines Maintenance Interval Schedule - C11 , C13 , and C15 Engines with Standard (Deep) Oil Sumps

345B Excavator Machine System Specifications Track Roller Mounting

Repair Procedure for Damaged Harness Wiring {1408} Repair Procedure for Damaged Harness Wiring {1408}

CG137-08 and CG137-12 Industrial Engines Speed/Timing (Secondary) - Test

2011/07/14 Glow Plugs on Certain C6.6 Engines {1412}

2011/09/12 A New Gasket and a New Spacer Plate are Now Used on Certain Reman 3500 Engines {1100, 1201, 7555}

G3406 Engine Spark Plugs - Inspect/Adjust/Replace

G3512 Gas Engine Flywheel

3516C Generator Set Engines Flywheel Housing

3512B and 3512C Petroleum Generator Set Engines Flywheel Housing Cover

3500C Marine Engines Vibration Damper Guard

CG137-08 and CG137-12 Engines Rotary Actuator (Carburetor) - Remove and Install - G3412B

CG137-08 and CG137-12 Engines Rotary Actuator (Gas Pressure Regulator) - Remove and Install

CG137-08 and CG137-12 Engines Carburetor - Remove and Install

CG137-08 and CG137-12 Engines Transformer - Remove and Install

CG137-08 and CG137-12 Engines Spark Plugs - Remove and Install

CG137-08 and CG137-12 Industrial Engines Aftercooler

CG137-08 and CG137-12 Engines Spark Plug Adapter - Remove and Install

CG137-08 and CG137-12 Industrial Engines Aftercooler - Test