Auxiliary Water Pump
Show/hide table
Illustration 1 | g02587796 |
Left side view |
Show/hide table
Illustration 2 | g02587916 |
Rear view |
Show/hide table
Specification for 264-7810 Auxiliary Sea Water Pump Gp     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 3     | 8T-2226 Screw     | Torque to 11 ± 3 N·m (95 ± 27 lb in).     |
2     | 1     | 5S-7383 Bolt     | Use the following procedure to tighten the bolt: 1. Torque to 55 ± 7 N·m (41 ± 5 lb ft). 2. Tap the bolt lightly with a hammer. 3. Again, torque to 55 ± 7 N·m (41 ± 5 lb ft).     |
3     | As required, use the following shims on each side of the impeller to obtain an axial clearance of 0.35 to 0.45 mm (0.014 to 0.018 inch).     |
||
1 | 100-3061 Shim     | Thickness is 0.127 mm (0.0050 inch).     |
|
1 | 100-3062 Shim     | Thickness is 0.254 mm (0.0100 inch).     |
|
1 | 100-3063 Shim     | Thickness is 0.305 mm (0.0120 inch).     |
|
1 | 100-3064 Shim     | Thickness is 0.381 mm (0.0150 inch).     |
|
4     | 1     | 100-3081 Locknut     | Torque to 40 ± 5 N·m (30 ± 4 lb ft).     |
5     | 1     | 104-6641 Bearing Locknut     | Torque to 40 ± 5 N·m (30 ± 4 lb ft).     |
6     | -     | -     | Fill the bearing cavity with clean grease.     |
7     | 1     | 352-1689 Impeller     | Apply blue Loctite 242 to the threads.     |
8     | 1     | 352-1688 Impeller     | Apply blue Loctite 242 to the threads.     |
9     | 2     | 186-0128 O-Ring Seal     | Lubricate the bore lightly with the rubber lubricant that is being sealed.     |
10     | 1     | 3J-7354 O-Ring Seal     | Lubricate the bore lightly with the rubber lubricant that is being sealed.     |
A     | 1     | 151-5705 Manifold     | Orient within 22.5 ± 5.0 degrees from the horizontal position.     |
C     | 1     | 153-9075 Manifold     | Orient within 22.5 ± 5.0 degrees from the horizontal position.     |
D     | 2     | 3N-8220 Clamp As     | Orient within 11 ± 5 degrees from the horizontal position.     |
Caterpillar Information System:
3516C Engine Control Cabinet - Disassemble - <B>374-2499</B> Control Cabinet Gp
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Atmospheric Pressure Sensor
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Crankcase Pressure Sensor
C32 Marine and Auxiliary Marine Engines Heat Exchanger
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Turbocharger Exhaust Temperature Sensor
C27 and C32 Engines for Caterpillar Built Machines Cylinder Block
3176C and 3196 Engines for Caterpillar Built Machines Turbocharger Outlet Pressure Sensor
C27 Generator Set Fuel System Primary Filter/Water Separator - Drain
3512C SR4B Generator Sets Safety Messages
70 Pin Connector Guide for TH55-E70-3512CP Petroleum Power Train Package{7451, 7553, 7566} 70 Pin Connector Guide for TH55-E70-3512CP Petroleum Power Train Package{7451, 7553, 7566}
C27 Generator Set Single Unit Operation
3516C Engine Selective Catalytic Reduction Module - Assemble - <B>374-2501</B> Catalytic Converter Gp
G3406 and G3412 Generator Set Engines Water Pump
3516C Engine Control Cabinet - Assemble - <B>374-2499</B> Control Cabinet Gp
XQ400 Power Module Water Pump - Inspect
3516B HD Generator Set Alarms and Shutoffs
2011/06/08 An Improved Fuel Priming Pump Gasket Is Now Used on Certain Commercial Engines {1258, 7555}
2011/06/08 An Improved Fuel Priming Pump Gasket Is Now Used on Certain Machine Engines {1258, 7555}
Cat Water Delivery System (WDS) Caterpillar Reference Material
C15 Generator Sets Product Installation
XQ400 Power Module Coolant Temperature Regulator - Replace
CG137-08 and CG137-12 Engines Coolant Sample (Level 1) - Obtain
Cat Water Delivery System (WDS) Hydraulic Oil Filter - Replace
Cat Water Delivery System (WDS) Hydraulic System Oil Sample - Obtain