Gear Group (Rear)
Show/hide table
| |
| 图 1 | g03324889 |
Show/hide table
| |
| 图 2 | g03324890 |
Show/hide table
| |
| 图 3 | g03324891 |
Show/hide table
| 技术规格 - 124-8395 后齿轮总成、 175-5204 后齿轮总成、 101-0835 后齿轮总成、 334-5298 后齿轮总成和 175-5203 后齿轮总成 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 2 | 凸轮轴驱动齿轮 | 组装前，使用饱含清洁液的无绒布擦去多余的机油，清洁凸轮轴锥面和凸轮轴驱动装置的锥形孔。 用酒精片清洁。
有关左右凸轮轴驱动齿轮的安装步骤，请参见拆解与组装。 |
| 2 | 2 | 惰轮组件 | 安装后，惰轮组件上的 125-9751 衬套孔径为 衬套的安装深度为 |
| 3 | 2 | 101-1368 止推垫圈 | 新止推垫圈的厚度为 |
| 4 | 1 | 齿轮组件 | 安装后，齿轮组件上的 101-1372 衬套孔径为 衬套的安装深度为 |
| 5 | 4 | 8M-2530 螺栓 | 拧紧至扭矩为 |
| 6 | 1 | 101-1366 齿轮轴 | 直径为 |
| 7 | 2 | 9X-8887 螺栓 | 按以下步骤拧紧凸轮轴驱动齿轮的螺栓： 1. 拧紧凸轮轴驱动齿轮的螺栓至扭矩 2. 在凸轮轴驱动齿轮的螺栓头处画一条垂直线。 参考图 2。 3. 用冲头顶住凸轮轴驱动齿轮固定板。 用锤子敲击冲头 3 到 4 次。 4. 再次将凸轮轴驱动齿轮的螺栓拧紧至 5. 重复步骤 3 和步骤 4，直到螺栓上的标记至少转过 90 度。 参考图 3。 |
| 8 | 4 | 1B-4367 螺栓 | 拧紧至扭矩为 |
| 9 | 2 | 8S-2331 螺栓 | 拧紧至扭矩为 |
| 10 | 1 | 101-1365 止推片 | 新止推片的厚度为 |
| 11 | 1 | 101-1370 曲轴齿轮 | 齿轮组件 (4) 上的标记必须与曲轴齿轮 (11) 上的标记对准。 |
| 12 | 2 | 101-1367 惰轮轴 | 直径为 |
Caterpillar Information System:
G3500 Engines Gear Group (Front)
C27 and C32 Engines for Caterpillar Built Machines Housing (Front)
C175-16 Marine Propulsion Engines Vibration Damper Guard
3500 Industrial Engines Crankshaft
C27 and C32 Engines for Caterpillar Built Machines Housing (Rear)
C15 and C18 Industrial Engines Vibration Damper
G3406 Engine Coolant - Change
CX31 and CX31 HT On-Highway Transmissions Transmission Hydraulic Control
C13, C15, and C18 Tier 4 Final Engines Camshaft
Network Management Card with Modbus for the UPSB505 Uninterruptible Power Supply Administration: Security
Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551} Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551}
Communication Adapter II{0600, 0709, 7600, 7610} Communication Adapter II{0600, 0709, 7600, 7610}
3508B Engine for Caterpillar Built Machines Balancer Group (Front)
CG137-08 and CG137-12 Engines Crankcase Blowby - Test/Record
XQ400 Power Module Driven Equipment - Check
3406C Generator Sets Refill Capacities
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Metal Particle Detector
Network Management Card with Modbus for the UPSB505 Uninterruptible Power Supply Administration: Network Features
3516B Generator Set Engines with Dynamic Gas Blending Metal Particle Detector - Test
CG137-08 and CG137-12 Engines Engine Oil and Filter - Change
CG137-08 and CG137-12 Engines Engine Oil Sample - Obtain
C27 and C32 Tier 4 Final Marine Engines Piston and Rings
325D and 329D Excavators Machine System Specifications Hydraulic Pedal Control (Auxiliary)
349F and 352F Excavators Machine System Specifications Pressure Reducing Valve (Boom Priority)