Engine Oil Pump
Show/hide table
Illustration 1 | g02573162 |
Show/hide table
NOTICE |
---|
Before operation, the pump must be lubricated with clean engine oil and the pump must turn freely by hand or damage to parts can be the result. |
Show/hide table
Specification for the 4N-0733 Engine Oil Pump Gp and 4n-8734 Engine Oil Pump Gp | |||
Item | Qty | Part | Specification Description |
- | - | - | Flush 8S-6511 Bushing with the face of the pump cover. |
1 | 1 | 2S-2760 Spring | Length under test force is |
Test force is |
|||
Approximate free length after test is |
|||
A | 1 | 4N-5273 Pump Drive Shaft | Diameter of pump drive shaft is Bore in oil pump cover for pump drive shaft is |
B | 1 | 1W-7240 Gear | Length of the gear is |
Depth of bore is |
|||
2 | 1 | - | Install the bushings so that the bushings are even with the outside of the oil pump body.
Angle from the centerline of the oil pump body to the bushing joint of the bushing is 30 ± 15 degrees. |
D | 1 | 8M-8489 Dowel | Installation depth of the dowel in the oil pump is |
E | 1 | - | Installation depth of the bushing in the oil pump housing is |
Caterpillar Information System:
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Connecting Rod
C175-16 Marine Propulsion Engines Exhaust Flange
C175-16 Marine Propulsion Engines Exhaust Flange
C15 On-highway Engine Connecting Rod
3500 Engines Piston and Rings - Two-Piece Piston
Network Management Card with Modbus for the UPSB505 Uninterruptible Power Supply Information Logs
CX31 and CX31 HT On-Highway Transmissions Oil Filter (Transmission)
2011/10/03 An Improved Lubrication System is Now Used on the TH48-E80 Petroleum Transmission {3030}
CX31 and CX31 HT On-Highway Transmissions Relief Valve (Transmission Hydraulic Control)
3500 Engines Cylinder Block
C15 and C18 Industrial Engines Water Lines
C15 Petroleum Engines Alternator Problem - Charging Problem and/or Noisy Operation
CX31 and CX31 HT On-Highway Transmissions Transmission Planetary
C27 and C32 Engines for Caterpillar Built Machines Gear Group (Front)
3500 Engines Connecting Rod and Main Bearing Journals
3500 Engines Crankshaft
3500B Locomotive Engines Crankshaft
3406C Generator Sets Plate Locations and Film Locations
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679} Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Communication Adapter II{0600, 0709, 7600, 7610} Communication Adapter II{0600, 0709, 7600, 7610}
Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551} Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551}
Network Management Card with Modbus for the UPSB505 Uninterruptible Power Supply Administration: Security