Connecting Rod
Show/hide table
图 1 | g03324908 |
Show/hide table
图 2 | g03324909 |
G-G 视图 |
Show/hide table
技术规格 - 144-0725 连杆组件 | |||
项目 | 数量 | 零件 | 技术规格说明 |
A | - | - | 套筒轴承任一面轴承接头中线上用于安装活塞销的角度为 10 度。 |
B | - | - | 安装活塞销的衬套前,必须从 |
C | 1 | 118-1655 衬套 | 在装配活塞和连杆前用清洁的发动机机油彻底润滑活塞销。
安装衬套后衬套上用于活塞销的孔径为 连杆上的衬套孔径为 |
D | - | - | 轴承中心间的距离为 |
E | 1 | 7N-2043 定位销 | 定位销在连杆盖上的突出量为 |
F | - | - | 向连杆螺栓施加最终扭矩后,曲轴连杆轴颈的轴承连杆孔径为 |
1 | - | - | 在连杆和连杆盖的这个位置,蚀刻下气缸编号。 将编号标记在连杆和连杆盖上。 在连杆与轴承挡圈凹口相同一侧上标上编号。 |
2 | - | - | 将连杆和活塞总成安装至发动机时,该斜面侧必须与曲轴销止推面相邻。 |
3 | - | - | 用于正确安装连杆盖的定位销 |
4 | 4 | 7N-2405 螺栓 | 采用以下步骤拧紧连杆螺栓: 螺栓 1 和螺栓 2 必须在具有轴承止动舌和定位销 (3) 的连杆盖的同一端。 1. 组装前,将 Molylube 涂覆在螺栓螺纹、螺栓杆和螺栓座上。 2. 接着,将螺栓 1 和螺栓 2 拧紧至 3. 接着,将螺栓 3 和螺栓 4 拧紧至 4. 然后,再将螺栓 3 和螺栓 4 拧紧至 5. 将各螺栓多拧紧 90 ± 5 度。 |
同一个新曲轴销上的两个连杆之间的侧隙为 |
Caterpillar Information System:
C175-16 Marine Propulsion Engines Exhaust Flange
C175-16 Marine Propulsion Engines Exhaust Flange
C15 On-highway Engine Connecting Rod
3500 Engines Piston and Rings - Two-Piece Piston
Network Management Card with Modbus for the UPSB505 Uninterruptible Power Supply Information Logs
CX31 and CX31 HT On-Highway Transmissions Oil Filter (Transmission)
2011/10/03 An Improved Lubrication System is Now Used on the TH48-E80 Petroleum Transmission {3030}
CX31 and CX31 HT On-Highway Transmissions Relief Valve (Transmission Hydraulic Control)
3500 Engines Cylinder Block
C15 and C18 Industrial Engines Water Lines
C15 Petroleum Engines Alternator Problem - Charging Problem and/or Noisy Operation
3500B Engines for Caterpillar Built Power Modules Cylinder Block
3406C Engines for Caterpillar Built Machines Engine Oil Pump
CX31 and CX31 HT On-Highway Transmissions Transmission Planetary
C27 and C32 Engines for Caterpillar Built Machines Gear Group (Front)
3500 Engines Connecting Rod and Main Bearing Journals
3500 Engines Crankshaft
3500B Locomotive Engines Crankshaft
3406C Generator Sets Plate Locations and Film Locations
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679} Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Communication Adapter II{0600, 0709, 7600, 7610} Communication Adapter II{0600, 0709, 7600, 7610}
Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551} Replacing Sleeve Bearings in Tyrone Gear Pumps and Motors (Used on Series 7 and 8, Iron and Aluminum Housings){0738, 5061, 5073, 7551}