Inlet and Exhaust Valve Guides - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A.     | 4C-6366     | 气门导管冲头     | 1     |
开始:
- 拆下进气门和排气门。 请参阅拆解和组装, "进气门和排气门 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 从缸盖组件上拆下气门导管 (1) 。
Show/hide table
图 1 | g02167333 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A.     | 4C-6366     | 气门导管冲头     | 1     |
B     | 362-5404     | 导向圈     | 1     |
C     | -     | 直尺     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将清洁的发动机机油涂抹到气门导管的外径和内径上。 将气门导管放置到缸盖中。 轻敲气门导管的顶部。 此动作可将进气门导管和排气门导管敲入缸盖组件中。
Show/hide table
图 2 | g02166659 |
此照片显示了缸盖和工具的剖面图。 |
Show/hide table
图 3 | g02166757 |
- 使用工具 (A) 和工具 (B) 安装气门导管。 将直尺横放在气门室盖底座密封表面上。 从气门导管的顶部到直尺的底部进行测量。 这个测量值称为距离 (C) 。 距离 (C) 应为 48.9 ± 0.5 mm (1.93 ± 0.02 in)。
End By: 安装进气门和排气门。 请参阅 拆解和组装, "进气门和排气门 - 拆卸和安装"。
Caterpillar Information System:
358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684} 358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}
2010/08/26 A Prelube Pump Is Available for C175-16 Generator Sets {1307, 1319}
797F Off-Highway Truck Hydraulic System Worksheets
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Quick Coupler - Lubricate - Mechanical Pin Grabber Quick Coupler (If Equipped)
Reusability Inspection of Seal Ring and Stator Carrier Assemblies for Certain Models {0760, 0761, 3101, 3129, 3160, 7555} Reusability Inspection of Seal Ring and Stator Carrier Assemblies for Certain Models {0760, 0761, 3101, 3129, 3160, 7555}
Procedure to Unlock the 341-8700 Fuel Injection Pump Gp {1251} Procedure to Unlock the 341-8700 Fuel Injection Pump Gp {1251}
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Quick Coupler Operation - Mechanical Pin Grabber Quick Coupler (If Equipped)
C9.3 Tier 4 Interim Engines Cooling Fan Reversing - Test
2011/06/29 A New Halogen Lamp Is Now Available for Certain Cat Products {1434}
LC5000, LC6100, and LC7000 Electric Power Generation Exciter Field - Flash
LC5000, LC6100, and LC7000 Electric Power Generation Resistor - Test
LC5000, LC6100, and LC7000 Electric Power Generation Generator Operation
C27 Petroleum Generator Set Engines Coolant Level - Test
C27 Generator Set Engines Acceleration Is Poor or Throttle Response Is Poor
C18 Generator Set Engine Oil and Filter - Change
Procedure for Installing the 296-0014 Prelubrication Oil Pump Gp on C175 Generator Sets{1307, 1319} Procedure for Installing the 296-0014 Prelubrication Oil Pump Gp on C175 Generator Sets{1307, 1319}
C27 and C32 Tier 4 Engines Diagnostic Capabilities
C27 Petroleum Generator Set Engines Exhaust Has Black Smoke
C27 Petroleum Generator Set Engines Fuel Pressure Is Low
C15 and C18 Tier 4 Final Engines Engine Oil Pressure - Test
C175-16 Marine Propulsion Engines Alternator Mounting
C7.1 Industrial Engine and Generator Set ARD Failed to Ignite
C27 Petroleum Generator Set Engines Intake Manifold Air Temperature Is High
C27 and C32 Engines for Caterpillar Built Machines Aftercooler - Test - If Equipped