Sensors and Electrical Components - MCS Switches and Alarms
Show/hide table
图 1 | g02163249 |
典型示例 |
冷却液液位开关由面板供电。 报警器可以被来自冷却液液位开关的信号激活。 有两种不同类型的冷却液液位开关。 一种开关用于膨胀箱上。 另一种则专门用于散热器。
Show/hide table
图 2 | g02161574 |
典型示例 |
冷却液差压开关由面板供电。 如果接收到不正确的信号,报警器将在接收到来自冷却液差压开关的信号时由控制面板激活。
生水差压开关由面板供电。 如果接收到不正确的信号,报警器将在接收到来自生水差压开关的信号时由控制面板激活。
Show/hide table
图 3 | g02161576 |
典型示例 |
冷却液温度发送器由面板供电。 冷却液温度发送器用于显示冷却液温度和触发警报定点。
如果冷却液温度过高,系统会发送信号给面板。
Show/hide table
图 4 | g02161577 |
典型示例 |
燃油压力开关由面板供电。
燃油滤清器的进口油压和出口油压受到监控。
Show/hide table
图 5 | g02161578 |
典型示例 |
油压发送器由面板供电。 如果接收到不正确的信号,报警器将在接收到来自油压发送器的信号时由控制面板激活。
油压开关可发送信号给控制面板,以关闭发动机。
机油滤清器的进口油压和出口油压受到监控。
Show/hide table
图 6 | g02161579 |
典型示例 |
如果油温过高,发送器将发送信号给面板。
注: 系统使用磁电转速传感器以在出现超速情况时关闭发动机。
Caterpillar Information System:
C4.4 (Mech) Marine Generator Set MCS-3 Overspeed
C4.4 (Mech) Marine Generator Set MCS-3 Gauges and Indicators
C4.4 (Mech) Marine Generator Set MCS-3 Model View Illustrations
C4.4 (Mech) Marine Generator Set MCS-3 Plate Locations and Film Locations
C4.4 (Mech) Marine Generator Set MCS-3 Emissions Certification Film
C4.4 (Mech) Marine Generator Set MCS-3 Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
C4.4 (Mech) Marine Generator Set MCS-3 Engine Air Cleaner Service Indicator - Inspect
C4.4 (Mech) Marine Generator Set MCS-3 Engine Mounts - Inspect
C4.4 (Mech) Marine Generator Set MCS-3 Engine Oil Level - Check
C4.4 (Mech) Marine Generator Set MCS-3 Engine Oil Sample - Obtain
C4.4 (Mech) Marine Generator Set MCS-3 Engine Protective Devices - Check
C4.4 (Mech) Marine Generator Set MCS-3 Engine Valve Lash - Check
2010/04/22 Improvement Made to the Harness in the Right-Hand Side Cab Console for Certain Excavators {1408}
C4.4 (Mech) Marine Generator Set MCS-3 Declaration of Conformity
C7.1 Marine Generator Set Generator Winding Insulation - Test
C4.4 (Mech) Marine Generator Set MCS-3 Safety Messages
797F and 797F XQ Off-Highway Trucks Machine Systems Tire and Rim (Front) - Remove and Install
797F Off-Highway Truck Power Train Tire and Rim (Rear) - Remove and Install
C9.3 Marine Engines Fastener Group (Vibration Damper)
2010/06/10 Procedure To Check Crankshaft Deflection in 3600 and C280 Engines {1202}
2010/04/16 A New Strainer Is Used on the Air Starting Systems of Certain C18 and C32 Engines {1451}
XQ Auto Paralleling Safety Messages
XQ Auto Paralleling Electrical System
XQ Auto Paralleling General Information