Piston Motor (Brake Cooling) - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 螺杆 (M5 x 0.8) (2)     | 1     |
5C-2874 | 螺母     | 1     | |
4B-4274 | 垫圈     | 1     | |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 1U-6344     | 螺杆     | 2     |
139-6366 | 螺母     | 8     | |
5P-8247 | 硬垫圈     | 8     | |
126-7176 | 顶出螺钉     | 1     | |
8T-9139 | 齿座     | 1     | |
1U-9895 | 十字挡块     | 1     | |
3H-0465 | 推拉工具盘     | 4     | |
6B-6683 | 螺母     | 1     | |
5P-8247 | 硬垫圈     | 1     | |
D     | 1P-1860     | 挡圈钳     | 1     |
F     | 6V-3009     | 横杆     | 1     |
6V-4832 | 螺钉     | 1     | |
1P-0457 | 盘     | 1     | |
126-7181 | 盘     | 2     | |
6V-3823 | 螺栓     | 2     | |
5P-8245 | 垫圈     | 2     | |
G     | 6V-2012     | 深度千分尺     | 1     |
H     | -     | Loctite 242     | -     |
J     | 6V-2055     | 润滑脂     | 1     |
Show/hide table
( 2 ) | 切割长度至 75 mm (3 in) |
- 使用合适的压具将轴承 (23) 安装到轴 (20) 上。
Show/hide table
图 1 | g02141774 |
- 使用工具 (D) ,将挡圈 (22) 安装到轴 (20) 上。
Show/hide table
图 2 | g02141693 |
- 将密封件 (14) 安装到盖 (11) 中。 将垫片 (13) 、盖 (11) 和挡圈 (9) 安装到轴 (20) 上。
Show/hide table
图 3 | g02141862 |
- 使用卡尺来测量轴承组件。 从表面 (A) 到表面 (B) 的正确尺寸为 99.50 + 0.0 − 0.100 mm ( 3.917 + 0.00 − 0.0039 inch)。 该测量确定旋转总成的正确角度。
Show/hide table
图 4 | g02126708 |
- 如有必要,增加或减少垫片 (13) 。
- 获得正确的尺寸后,将挡圈 (9) 、盖 (11) 和垫片 (13) 从轴 (20) 上拆下。
- 将销 (21) 和活塞 (15) 安装到板 (19) 中。
Show/hide table
图 5 | g02141766 |
- 将活塞 (15) 和板 (19) 安装到轴上。 将工具 (H) 涂覆到螺钉 (18) 上。 安装螺钉 (18) 至扭矩为 15.5 ± 1.5 N·m (137 ± 13 lb in)。
Show/hide table
图 6 | g02141638 |
- 将弹簧 (16) 安装到活塞筒组件 (8) 中。 此时先不要安装垫片。
Show/hide table
图 7 | g02141875 |
- 将活塞筒组件 (8) 安装到活塞 (15) 上。 将工具 (B) 安装到活塞筒组件 (8) 中。
Show/hide table
图 8 | g02140734 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将壳体 (3) 加热到 80 °C (176 °F)。 冷却旋转总成 (10) 。
Show/hide table
图 9 | g02142077 |
- 将旋转总成安装到壳体 (3) 中。
- 安装步骤 4 中确定的垫片 (13) 。 将 O 形密封圈 (12) 安装到壳体中。
Show/hide table
图 10 | g02142402 |
- 安装盖 (11) 。 使用工具 (B) 安装挡圈 (9) 。
Show/hide table
图 11 | g02142405 |
- 将工具 (A) 从活塞筒组件 (8) 上拆下。
Show/hide table
图 12 | g02140683 |
- 将板 (7) 安装到壳体 (3) 中。
Show/hide table
图 13 | g02142417 |
- 将壳体 (3) 放在软口台钳中。 将工具 (F) 安装到壳体 (3) 上。 使用工具 (G) 以便测量板的深度。 在一个以上的位置进行测量。 拧紧工具 (F) 上的螺栓。 继续下推,直至遇到阻力为止。 不要用力。 再次测量至板的深度。 记录两次测量的差值。 从该测量值中减去 0.20 ± .0.05 mm (0.008 ± 0.002 in)。 这是步骤 23 中将要安装的垫片 (17) 的正确厚度。 拆下工具 (F) 和工具 (G) 。
Show/hide table
图 14 | g02142427 |
- 将板 (7) 从壳体 (3) 上拆下。
Show/hide table
图 15 | g02142417 |
- 将工具 (A) 安装到活塞筒组件 (8) 中。
Show/hide table
图 16 | g02140683 |
- 使用工具 (C) ,以便拉拔出旋转总成 (10) 、盖 (11) 、O 形密封圈 (12) 和垫片 (13) 。
Show/hide table
图 17 | g02126683 |
- 将工具 (A) 从活塞筒组件 (8) 上拆下。 将活塞筒组件 (8) 从活塞 (15) 上拆下。
Show/hide table
图 18 | g02140734 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将弹簧 (16) 从活塞筒组件 (8) 上拆下。
Show/hide table
图 19 | g02141875 |
- 安装步骤 17 中确定的垫片 (17) 。 将弹簧 (16) 安装到油缸筒 (8) 中。
Show/hide table
图 20 | g02141632 |
- 将活塞筒组件 (8) 安装到活塞 (15) 上。 将工具 (B) 安装到活塞筒组件 (8) 中。
Show/hide table
图 21 | g02140734 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将壳体 (3) 加热到 80 °C (176 °F)。 冷却旋转总成 (10) 。
Show/hide table
图 22 | g02142077 |
- 将旋转总成安装到壳体 (3) 中。
- 安装步骤 4 中确定的垫片 (13) 。 将 O 形密封圈 (12) 安装到壳体中。
Show/hide table
图 23 | g02142402 |
- 安装盖 (11) 。 使用工具 (B) 安装挡圈 (9) 。
Show/hide table
图 24 | g02142405 |
- 将工具 (A) 从活塞筒 (8) 上拆下。
Show/hide table
图 25 | g02140683 |
- 将 O 形密封圈 (6) 安装到壳体 (3) 上。 利用将要使用的机油润滑活塞筒 (8) 的表面。
Show/hide table
图 26 | g02142973 |
- 使用工具 (J) 以便将板 (7) 附着到盖 (5) 上。
Show/hide table
图 27 | g02143104 |
- 将盖 (5) 放在壳体 (3) 上。
Show/hide table
图 28 | g02126571 |
- 安装螺栓 (4) 。
- 将弯头 (2) 和传感器 (1) 安装到壳体 (3) 上。
Show/hide table
图 29 | g02126548 |
End By: 安装活塞马达。
Caterpillar Information System:
797F and 797F XQ Off-Highway Trucks Machine Systems Piston Motor (Brake Cooling) - Disassemble
797F and 797F XQ Off-Highway Trucks Machine Systems Oil Cooler Core (Steering) - Remove and Install
CG137-12 Petroleum Generator Set Engine Turbocharger Oil Lines
G3516 Engines Fuel Filter
G3512E Generator Set Engines Turbocharger
797F Off-Highway Truck Power Train Oil Cooler Core (Power Train) - Remove and Install
2010/03/31 The 1U-8846 Gasket Sealant Is Cancelled {7555}
2010/03/22 The 1U-8846 Gasket Sealant Is Cancelled {7555}
2011/02/02 The 1U-8846 Gasket Sealant Is Canceled {7555}
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 0585 - FMI 02
C15 and C18 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install - For Series Turbocharger Applications
C18 Industrial Engines Configuration Parameters
2010/03/29 Proper Maintenance of the Cooling Systems of Certain Commercial ACERT C32 Marine Engines {1350, 1395}
Proper Maintenance of the Cooling Systems of Certain Commercial Marine Engines With Keel Cooling {1350, 1395} Proper Maintenance of the Cooling Systems of Certain Commercial Marine Engines With Keel Cooling {1350, 1395}
C11 and C13 Engines Air Lines
G3512 Gas Engine Exhaust Fitting
G3512 Gas Engine Exhaust Fitting
G3516C and G3516E Gas Engines Cover Group (Front Housing)
797F and 797 XQ Off-Highway Trucks Engine Supplement Expansion Tank - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Soot Sensor - Test
EMCP4.3/4.4 General Information
797F and 797F XQ Off-Highway Trucks Machine Systems Rear Suspension (Cylinder) - Remove and Install
797F and 797 XQ Off-Highway Trucks Engine Supplement Piston Motor (Fan Drive) - Disassemble
797F and 797 XQ Off-Highway Trucks Engine Supplement Piston Motor (Fan Drive) - Assemble