Oil Cooler Core (Steering) - Remove and Install
拆卸步骤
Show/hide table
高温机油或高温部件可能会导致人身伤害。 在工作温度下,机油温度高,压力高。 热油能造成烫伤。 只能在发动机停机且加注口盖充分冷却到可以徒手触及时再卸下加注口盖。 不让高温油或部件与皮肤接触。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下机具和其油路之前,必须先把机具放到地面上,让油先冷却,才可进行工作。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
在工作温度下,发动机冷却液是热的,并且带有压力。 蒸汽还会引起人身伤害。 只有在发动机已关闭且加注口盖冷却到可徒手触摸后,才能检查冷却液液位。 缓慢卸下加注口盖,释放其中压力。 冷却系统添加剂含碱。 应避免皮肤和眼睛与其接触,以防造成人身伤害。 |
- 释放系统压力。 请参阅操作和保养手册, "系统压力释放"。
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "液压油箱 - 更换 - 转向系统"。
- 将发动机冷却液排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 拆下管组件 (1) 。
Show/hide table
图 1 | g02126524 |
- 断开软管组件 (2) 。 断开管组件 (3) 。
Show/hide table
图 2 | g02126525 |
- 拆下卡箍 (4) 。 断开软管组件 (5) 。 拆下管组件 (2) 。
Show/hide table
图 3 | g02126539 |
- 断开软管组件 (6) 。 断开管组件 (7) 。
Show/hide table
图 4 | g02126542 |
- 拆下卡箍 (8) 。 断开软管组件 (9) 。 拆下管组件 (7) 。
Show/hide table
图 5 | g02126547 |
- 断开管组件 ( 10) 。
Show/hide table
图 6 | g02126553 |
- 将适当的起吊设备连接到油冷却器 (11) 上。 机油冷却器 (11) 的重量约为 57 kg (125 lb)。 安装螺栓 (12) 和间隔套。
Show/hide table
图 7 | g02126555 |
Show/hide table
图 8 | g02126565 |
- 拆下螺栓 (13) 和隔套。
- 拆下机油冷却器 (11) 。
安装步骤
- 按相反顺序安装油冷却器 (11) 。
Caterpillar Information System:
CG137-12 Petroleum Generator Set Engine Turbocharger Oil Lines
G3516 Engines Fuel Filter
G3512E Generator Set Engines Turbocharger
797F Off-Highway Truck Power Train Oil Cooler Core (Power Train) - Remove and Install
2010/03/31 The 1U-8846 Gasket Sealant Is Cancelled {7555}
2010/03/22 The 1U-8846 Gasket Sealant Is Cancelled {7555}
2011/02/02 The 1U-8846 Gasket Sealant Is Canceled {7555}
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 0585 - FMI 02
C15 and C18 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install - For Series Turbocharger Applications
C18 Industrial Engines Configuration Parameters
C15 and C18 Engines Engine Rating Definitions
2010/03/31 A New Rocker Arm Assembly Is Available for C15 Engines {1123}
797F and 797F XQ Off-Highway Trucks Machine Systems Piston Motor (Brake Cooling) - Disassemble
797F and 797F XQ Off-Highway Trucks Machine Systems Piston Motor (Brake Cooling) - Assemble
2010/03/29 Proper Maintenance of the Cooling Systems of Certain Commercial ACERT C32 Marine Engines {1350, 1395}
Proper Maintenance of the Cooling Systems of Certain Commercial Marine Engines With Keel Cooling {1350, 1395} Proper Maintenance of the Cooling Systems of Certain Commercial Marine Engines With Keel Cooling {1350, 1395}
C11 and C13 Engines Air Lines
G3512 Gas Engine Exhaust Fitting
G3512 Gas Engine Exhaust Fitting
G3516C and G3516E Gas Engines Cover Group (Front Housing)
797F and 797 XQ Off-Highway Trucks Engine Supplement Expansion Tank - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Soot Sensor - Test
EMCP4.3/4.4 General Information
797F and 797F XQ Off-Highway Trucks Machine Systems Rear Suspension (Cylinder) - Remove and Install