Pump Drive - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-7600     | 滑锤拉拔器总成     | 1     |
B     | 1P-0520     | 冲头总成     | 1     |
1P-5546 | 十字挡块     | 1     | |
5F-7366 | 顶出螺钉     | 1     | |
6V-5845 | 螺栓 (M20×2.5×70mm)     | 2     | |
8T-3282 | 硬垫圈 (M20)     | 2     | |
C     | 1P-0520     | 冲头总成     | 1     |
D     | 8B-7551     | 轴承拉拔器     | 1     |
E     | 1U-9895     | 十字挡块     | 1     |
1P-0520 | 冲头总成     | 1     | |
1P-2322 | 组合式拉拔器     | 1     | |
1P-0546 | 夹钳     | 2     | |
F     | 6V-7742     | 全高螺母     | 2     |
开始:
- 拆下泵驱动装置。
- 拆下软管组件 (1) 。 拆下六个螺栓 (2) 和垫圈。 拆下护罩组件 (3) 。 拆下轭组件 (4) 。
Show/hide table
图 1 | g00685893 |
- 使用工具 (A) 以便拆卸唇型密封 (5) 。
Show/hide table
图 2 | g00685899 |
- 定位泵驱动装置,如图所示。 标记螺栓以便安装时识别螺栓 (6) 和螺栓 (7) 。 拆下两颗螺栓 (6) 和垫圈。 卸下两条螺栓 (7) 和垫圈。 拆下板 (8) 。 拆下垫片组 (9) 。
Show/hide table
图 3 | g00688683 |
- 使用工具 (F) ,以拆下八个锥形锁紧螺柱 (11) 。 拆下十六根螺栓 (10) 和垫圈。
Show/hide table
图 4 | g00688685 |
- 为便于安装,标记轴承保持架 (13) 的顶部和轴承保持架 (12) 的底部。
- 将工具 (B) 安装到齿轮和底部轴承保持架 (12) ,如图所示。 使用工具 (B) 将底部轴承保持架 (12) 从箱体 (14) 上拆下。
Show/hide table
图 5 | g00688686 |
Show/hide table
图 6 | g00688687 |
- 对顶部轴承保持架 (13) 重复步骤 6。
- 将 O 形密封圈 (15) 从底部轴承保持架 (12) 上拆下。
Show/hide table
图 7 | g00688688 |
- 使用工具 (C) 将滚柱轴承外圈 (16) 从底部轴承保持架 (12) 上拆下。
Show/hide table
图 8 | g00688689 |
- 对顶部轴承保持架 (13) 重复步骤 8 和步骤 9。
- 将垫片组 (17) 和 (18) 从箱体 (14) 上拆下。
Show/hide table
图 9 | g00688690 |
- 将一条螺栓 (7) 安装到轴 (19) 中。 使用适当的撬棍和垫块将轴 (19) 从箱体 (14) 上拆下。
Show/hide table
图 10 | g00699051 |
- 将 O 形密封圈 (20) 和 O 形密封圈 (21) 从轴 (19) 上拆下。
Show/hide table
图 11 | g00699052 |
- 将顶部齿轮 (22) 和底部齿轮 (23) 从箱体 (14) 上拆下。
Show/hide table
图 12 | g00699053 |
- 将底部齿轮 (23) 和工具 (D) 定位到适当的压具上。 使用工具 (D) 和压具将滚柱轴承内圈 (24) 从底部齿轮 (23) 上拆下。
Show/hide table
图 13 | g00699056 |
- 将底部齿轮 (23) 在压具中翻转 180 度。 使用工具 (D) 和压具将滚柱轴承内圈 (25) 从底部齿轮 (23) 上拆下。
Show/hide table
图 14 | g00699058 |
- 将顶部齿轮 (22) 和工具 (D) 定位到适当的压具上。 使用工具 (D) 和压具将滚柱轴承内圈 (26) 从顶部齿轮 (22) 上拆下。
Show/hide table
图 15 | g00699060 |
- 将顶部齿轮 (22) 在压具中翻转 180 度。 使用工具 (D) 和压具将滚柱轴承内圈 (27) 从顶部齿轮 (22) 上拆下。
Show/hide table
图 16 | g00699062 |
- 将惰轮 (28) 从箱体 (14) 上拆下。
Show/hide table
图 17 | g00699063 |
- 将滚柱轴承内圈 (29) 从惰轮 (28) 上拆下。
Show/hide table
图 18 | g00699064 |
- 将内圈隔套 (30) 从滚柱轴承内圈 (31) 上拆下。
Show/hide table
图 19 | g00699066 |
- 将惰轮 (28) 抬离滚柱轴承内圈 (31) 。
- 使用导线电焊机焊接滚柱轴承外圈 (32) 整个内部周围的焊缝。 完成焊接步骤后,立即将滚柱轴承外圈 (32) 和轴承外圈隔套 (33) 从惰轮 (28) 上拆下。
Show/hide table
图 20 | g00699067 |
- 如有必要,将卡环 (34) 从惰轮 (28) 上拆下。
- 使用工具 (E) 将滚柱轴承外圈 (35) 从箱体 (14) 上拆下。
Show/hide table
图 21 | g00699069 |
Show/hide table
图 22 | g00699068 |
Show/hide table
注意 |
---|
请勿使用割炬拆下滚柱轴承外圈。 使用适当的工具拆下滚柱轴承外圈。 否则可能会导致零件损坏。 |
- 对其余的滚柱轴承外圈重复步骤 25。
- 标记接头 (36) 以便安装时识别其位置。 将接头 (36) 和 O 形密封圈从箱体 (14) 上拆下。 将排放塞 (37) 和 O 形密封圈从箱体 (14) 上拆下。
Show/hide table
图 23 | g00699071 |
- 将箱体 (14) 翻转 180 度。 使用工具 (F) ,以拆下四个锥形锁紧螺柱 (38) 。 将四根锥形锁紧螺柱 (38) 从箱体 (14) 上拆下。
Show/hide table
图 24 | g00699072 |
- 标记接头 (39) 、 (40) 和 (41) 以便在安装时识别它们的位置。 将接头 (39) 、 (40) 和 (41) 以及 O 形密封圈 从箱体 (14) 上拆下。
Caterpillar Information System:
3500 Engines Air Lines
C7.1 Industrial Engine and Generator Set ARD Fuel Supply - Test
C7.1 Industrial Engine and Generator Set Diesel Particulate Filter Has High Ash Load
797F and 797F XQ Off-Highway Trucks Fuel System Primary Filter (Water Separator) - Replace
797F and 797F XQ Off-Highway Trucks Fuel System Primary Filter (Water Separator) - Drain
797F and 797F XQ Off-Highway Trucks Hoist Screens - Clean
797F and 797F XQ Off-Highway Truck Power Train Electrical System
C32 Marine Engine Overhaul (Top End) - Engines Which are Rated "E"
3412C Generator Sets Declaration of Conformity
3412C Generator Sets Sound Information
Visual Inspection and Salvage Procedures for Aftercoolers in 3500 Engines {1063, 1063, 1379} Visual Inspection and Salvage Procedures for Aftercoolers in 3500 Engines {1063, 1063, 1379}
797F and 797F XQ Off-Highway Trucks Frame - Clean/Inspect
793F Off-Highway Truck Machine Systems Pump Drive - Assemble
Instructions For Installing The Window On Some Generator Set Enclosures{7274, 7310} Instructions For Installing The Window On Some Generator Set Enclosures{7274, 7310}
Filtration Times for Caterpillar Machine Fluid Compartments{0680, 0738, 0768, 3080, 5050, 5056, 5095} Filtration Times for Caterpillar Machine Fluid Compartments{0680, 0738, 0768, 3080, 5050, 5056, 5095}
797F and 797F XQ Off-Highway Trucks Hydraulic Tank Screen - Clean
797F and 797F XQ Off-Highway Trucks Magnetic Plug (Wheels) - Check
C7.1 Industrial Engine and Generator Set ARD Loss of Combustion
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216} Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
C13 and C15 On-highway Engines ARD Fuel Pressure Is High
797F and 797F XQ Off-Highway Trucks Pump Drive Return Screen - Clean - Transmission and Torque Converter System
797F and 797F XQ Off-Highway Trucks Radiator, Aftercooler and Air Conditioner Condenser - Clean
795F AC and 795F AC XQ Off-Highway Trucks Rollover Protective Structure (ROPS) - Inspect
CX31-P600 Petroleum Transmission Transmission Covers - Integral Pump Drives