Fuel Filter and Base - Remove and Install - Secondary Fuel Filter
参考: 专门说明书, "目视维修步骤 - 颜色和符号" M0066576。
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | - | 皮带式扳手 | 1 |
Show/hide table
| 注意 |
|---|
|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何作业之前，请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息，请参阅系统运作，测试和调整, "燃油系统部件清洁度"。 |
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 按照本地法规和要求处置所有油液。 |
- 将燃油供应转到断开位置。
- 将蓄电池断路开关转到断开位置。
- 排空细滤器。 参考操作和保养手册, "燃油系统细滤器 - 更换"以了解正确步骤。
Show/hide table
| |
| 图 1 | g06224419 |
Show/hide table
| |
| 图 2 | g06224420 |
Show/hide table
| |
| 图 3 | g06224423 |
Show/hide table
| |
| 图 4 | g06224424 |
Show/hide table
| |
| 图 5 | g06224425 |
- 按与拆卸相反的顺序安装燃油滤清器和底座。
Show/hide table
| |
| 图 6 | g06224426 |
Caterpillar Information System:
Retrofit Procedure to Install LED Lights on Certain 630G and 650G Wheel Tractor Scrapers {1429, 1431, 1434} Retrofit Procedure to Install LED Lights on Certain 630G and 650G Wheel Tractor Scrapers {1429, 1431, 1434}
320 GC, 320 and 323 Excavator Seat Belt - Inspect
C9.3B Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
Regulatory Compliance Information Product Link - PL631 - If Equipped
320 GC, 320 and 323 Excavator Mounting and Dismounting
320 GC, 320 and 323 Excavator Windows - Clean
Improved Radiator Hoses are Now Used on Certain D6T Track Type Tractors {1380} Improved Radiator Hoses are Now Used on Certain D6T Track Type Tractors {1380}
320, 323 Excavator Engine Supplement Refrigerant Condenser - Remove and Install
992K Wheel Loader Systems Axle Mounting
C27 and C32 Tier 4 Final Marine Engines Fuel Filter Base
992K Wheel Loader Systems Aftercooler - Air
C27 and C32 Tier 4 Final Marine Engines Fuel Filter (Primary)
854K Wheel Dozer Systems Bulldozer Pin
854K Wheel Dozer Systems Check and Relief Valve - Ripper
992K Wheel Loader Systems Check Valve (Steering Quad)
320, 323 Excavator Engine Supplement Electronic Control Module - Remove and Install
A New NOx Reduction System Cooler Group Is Now Used on All C9.3 Tier 4 Interim Machine Engines {108G} A New NOx Reduction System Cooler Group Is Now Used on All C9.3 Tier 4 Interim Machine Engines {108G}
MD6250 Rotary Drill Systems General Information (Air System)
MD6250 Rotary Drill Systems Location Of Components (Air System)
MD6250 Rotary Drill Systems Electronic Control (Air System)
MD6250 Rotary Drill Systems Air System - Compressed Air System
MD6250 Rotary Drill Systems Air Compressor
MD6250 Rotary Drill Systems General Information (Cooling System)
MD6250 Rotary Drill Systems Location of Components (Cooling System)