312D2 and 313D2 Excavators Caterpillar


Hydraulic System Oil Filter (Return) - Replace

Usage:

313D2 FEB

------ 警告! ------

熱機油和高溫組件會導致人員受傷。 請勿讓熱油或發熱的組件接觸到皮膚。




插圖 1g01442999

  1. 將機器停放於水平地面上。 將鏟斗降至地面,並使斗桿處於垂直位置。


    插圖 2g03159032
    (1) 螺栓
    (2) 墊圈
    (3) 頂蓋

  2. 拆下液壓油箱頂部的螺栓 (1)、墊圈 (2) 和檢修蓋 (3)。


    插圖 3g06112540

  3. 徹底清潔此區域,以清除回油濾清器蓋和加注蓋上的灰塵。

  4. 旋鬆加注蓋,以釋放液壓油箱的內部壓力。 壓力釋放後,請取下加注蓋。


    插圖 4g06112584
    (4) 緊固件
    (5) 墊圈
    (6) 頂蓋
    (7) 彈簧
    (8) 閥
    (9) 濾芯
    (10) O 型環密封件

    附註鬆開緊固件時,彈簧會將蓋子推出。

  5. 拆下緊固件 (4)、墊圈 (5) 及濾清器蓋 (6)。

  6. 拆下油箱上的彈簧 (7)、閥 (8) 及濾芯 (9)。

  7. 檢查 O 形環密封件 (10)。 如果 O 形環密封件有明顯磨損或損壞,請加以更換。

  8. 安裝新濾清器濾芯。

    附註濾芯上標有新濾清器濾芯的頂部。 請確保依照正確的方向安裝濾清器濾芯。

  9. 確認濾清器濾芯已正確安裝到位。 應將濾清器濾芯固定在濾清器外殼的中心,且不要傾斜,並位於凸緣下方約 40 mm (1.6 inch) 處。

  10. 將閥 (8)、彈簧 (7) 安裝到濾芯上。

  11. 裝上濾清器蓋 (6)、緊固件 (4) 及墊圈 (5)

  12. 清潔並裝上加注蓋。

  13. 裝上檢修蓋 (3)、螺栓 (1) 及墊圈 (2)。

Caterpillar Information System:

Changing the Pressure Reducing Valve Lowers the Risk for Leaks to Occur in the Brake Control Valve Group on Certain 988K Wheel Loaders {4264, 4265, 4282, 4293} Changing the Pressure Reducing Valve Lowers the Risk for Leaks to Occur in the Brake Control Valve Group on Certain 988K Wheel Loaders {4264, 4265, 4282, 4293}
950 GC Wheel Loader Hydraulic System Relief Valve (Line)
D6T Track Type Tractor Power Train Track - Separate
950 GC Wheel Loader Hydraulic System Relief Valve (Load Sensing Signal)
910M, 914M and 918M Wheel Loader Power Train Piston Pump (Hydrostatic) - Remove and Install
340F Excavator Machine Systems Coupler Lines
994K Wheel Loader Engine Supplement Vibration Damper and Pulley - Remove and Install
Installation Procedure for Product Link® PL161 System {7606} Installation Procedure for Product Link® PL161 System {7606}
Cat® Grade Control for D6N Track-Type Tractors Display Firmware Upgrade
Cat® Grade Control for D6K2 Track-Type Tractors Display Firmware Upgrade
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Speed/Timing - Test
854K Wheel Dozer Operator Controls
A New Setscrew is Now Used in the Cylinder Group on Certain 620K and 630K Wheel Tractor-Scrapers {5301, 5303, 5317} A New Setscrew is Now Used in the Cylinder Group on Certain 620K and 630K Wheel Tractor-Scrapers {5301, 5303, 5317}
D6T Track Type Tractor Power Train Torque Converter - Assemble
340F Excavator Machine Systems Coupler Lines
New Electronic Monitoring System (EMS) Series III and Software Are Now Available for Certain Wheel Tractor-Scrapers {7450, 7451, 7490, 7610, 7620} New Electronic Monitoring System (EMS) Series III and Software Are Now Available for Certain Wheel Tractor-Scrapers {7450, 7451, 7490, 7610, 7620}
340F Excavator Machine Systems Front Lines
994K Wheel Loader Engine Supplement Water Pump - Remove and Install
986K Wheel Loader TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565} 986K Wheel Loader TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565}
D6T Track Type Tractor Power Train Track - Connect
953K Track-Type Loader Power Train Recoil Spring - Remove and Install
C4.4 and C6.6 Engines Exhaust Has Excessive White Smoke
992K Wheel Loader Alternate Exit
992K Wheel Loader Mirror
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.