Machine Menu
Machine settings are used to install/uninstall, enable/disable, or change functions for various features on the machine.
Show/hide table
Illustration 1 | g06005068 |
Machine Menu |
From the Machine Settings menu, use the arrow button to highlight the desired parameter. Press the OK button to gain access to the highlighted parameter screen. Follow the screen prompts to adjust the parameter. All the parameters in this category relate to the operator preferences for the work tool operational modes. The following parameters can be adjusted:
- Stable Blade – Enabled, Disabled
- Blade Response – Fine, Standard, Fast
- Machine Response – Low, Medium, High
- Steering Modulation – Low, Medium, High
- Brake Pedal Decel – Enabled, Disabled
- Automatic Traction Control – Low, Medium, High
- Automatic Engine Speed – 300 sec, 240 sec, 180 sec, 120 sec, 90 sec, 60 sec, 30 sec, Disabled
- Fan Purge Duration – 60 sec, 40 sec, 25 sec, 15 sec, 10 sec, 5 sec
- Fan Purge Interval – 120 min, 90 min, 60 min, 45 min, 30 min, 20 min, 15 min
- Factory Settings
Show/hide table
Illustration 2 | g03870555 |
Blade Response screen |
Show/hide table
Illustration 3 | g06022536 |
Auto Engine Speed Control (AESC)
Show/hide table
Illustration 4 | g06008211 |
Show/hide table
Illustration 5 | g03870582 |
Disable the "Auto Engine Speed" feature to set a delay time. The "Delay Time" prior to auto engine speed engaging can be set from 3 to 60 seconds. If the "Auto Engine Speed" feature is enabled, no delay time can be set.
Caterpillar Information System:
D6K and D6K2 Track-Type Tractor Monitoring System Display Menu
910M, 914M, 918M, 910K, and 914K Wheel Loader Machine Systems Tilt Cylinder - Remove and Install
PL61 Pipelayer Maintenance Interval Schedule
950 GC Wheel Loader Braking and Hydraulic Fan System Hydraulic Fan System
PL61 Pipelayer Lubricant Viscosities - Fluids Recommendations
D6K and D6K2 Track-Type Tractor Monitoring System Diagnostic Operation
PL61 Pipelayer Battery Disconnect Switch
D6T XE Electrical & Hydraulic Troubleshooting Data - Transport
950 GC Wheel Loader Braking and Hydraulic Fan System Brake Control Valve (Parking)
814K Wheel Dozer Hydraulic Oil Cooler
950 GC Wheel Loader Braking and Hydraulic Fan System Brake Control Valve (Service)
814K Wheel Dozer Main Control Valve
312D2 and 313D2 Excavators Lubricant Viscosities - Fluids Recommendations
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Sensor Signal (Analog, Passive) - Test
D6K and D6K2 Track-Type Tractor Monitoring System Operator Profile Menu
D6K and D6K2 Track-Type Tractor Monitoring System Pop-Up Messages
D6K and D6K2 Track-Type Tractor Monitoring System Symptom Troubleshooting
D6K and D6K2 Track-Type Tractor Monitoring System Display Is Blank
312D2 and 313D2 Excavators Hydraulic System Oil - Change
D6K and D6K2 Track-Type Tractor Monitoring System Wiring Harness (Open Circuit) - Test
D6K and D6K2 Track-Type Tractor Monitoring System Wiring Harness (Short Circuit) - Test
D6K and D6K2 Track-Type Tractor Monitoring System Module - Replace
854K Wheel Dozer Operator Controls
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Speed/Timing - Test