Radiator Top Tank - Remove and Install - Jacket Water Heater
拆卸步骤
开始:
- 拆下膨胀水箱。 请参阅拆解和组装, "膨胀水箱 - 拆卸和安装"。
- 拆下另一个散热器顶部水箱。 请参阅拆解和组装, "散热器顶部水箱 - 拆卸和安装"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且散热器盖已经冷却到可以徒手触摸时,再慢慢拆下过滤器盖以释放压力。 冷却系统调节器含碱。 应避免它与皮肤和眼睛接触。 |
- 拆下软管 (1) 和支架 (2) 。
Show/hide table
图 1 | g01391928 |
- 松开卡箍 (3) 。 拆下螺栓 (4) 和散热器顶部水箱 (5) 。
Show/hide table
图 2 | g01391929 |
- 拆下密封 (6) 。
Show/hide table
图 3 | g01391932 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 207-1600 (1)     | 橡胶润滑剂     | -     |
207-1601 | 橡胶润滑剂     | -     |
Show/hide table
( 1 ) | 仅限 EAME |
- 将工具 (A) 涂抹在密封 (6) 上。 安装密封 (6) 。
Show/hide table
图 4 | g01391932 |
- 将散热器顶部水箱 (5) 放置到位并安装螺栓 (4) 。 拧紧卡箍 (3) 。
Show/hide table
图 5 | g01391929 |
- 安装支架 (2) 和软管 (1) 。
注: 安装膨胀水箱之后,再安装另外一个散热器顶部水箱。
Show/hide table
图 6 | g01391928 |
End By:
- 安装膨胀水箱。 请参阅 拆解和组装, "膨胀水箱 - 拆卸和安装"。
- 安装另一个散热器顶部水箱。 请参阅 拆解和组装, "散热器顶部水箱 - 拆卸和安装"。
Caterpillar Information System:
C15 and C18 Generator Set Engines Radiator Bottom Tank - Remove and Install - Jacket Water Heater
C9 Marine Generator Set Starting the Engine - Marine Certification Society (MCS) Control Panel
C6.6 Industrial Engine Engine Oil and Filter - Change
3176C, 3406E and 3456 Industrial Engines Engine Has Mechanical Noise (Knock)
G3500 A3 Engines Fuel Energy Content
C7.1 (Mech) Industrial Engine Alternator - Inspect
C6.6 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Governor - Adjust
C4.4 Industrial Engine Fuel Related Components in Cold Weather
C15 Petroleum Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Cooling System Coolant Sample (Level 2) - Obtain
C7 Petroleum Engine Speed Sensor - Clean/Inspect
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Head
3176C, 3406E and 3456 Industrial Engines Exhaust Temperature Is High
C15 and C18 Generator Set Engines Radiator Core - Remove and Install - Jacket Water Heater
C6.6 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install - Secondary Fuel Filter
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove