Fuel Injection Pump
Show/hide table
Illustration 1 | g01394088 |
(1) O-ring seal ... Lubricate the bore lightly with the lubricant that is being sealed.
(2) Minimum assembled backlash for pinion assembly ... 0.02 mm (0.001 inch)
(3) Press the pump drive gear so that the gear is flush with the shoulder of the pinion assembly.
(4) Minimum assembled backlash for bevel gear ... 0.02 mm (0.001 inch)
Show/hide table
Illustration 2 | g01394146 |
View B-B (5) Fuel injection pump |
(6) 8N-1415 Spring
- Length under test force ... 8.69 mm (0.342 inch)
- Test force ... 111.21 ± 6.45 N (25 ± 1.5 lb)
- Free length after test ... 12.12 mm (0.477 inch)
- Outside diameter ... 9.78 mm (0.385 inch)
- Test force ... 111.21 ± 6.45 N (25 ± 1.5 lb)
(7) 7N-1208 Spring
- Length under test force ... 29.26 mm (1.152 inch)
- Test force ... 325 ± 16.5 N (73.00 ± 3.65 lb)
- Free length after test ... 48.03 mm (1.891 inch)
- Outside diameter ... 25.27 mm (0.995 inch)
- Test force ... 325 ± 16.5 N (73.00 ± 3.65 lb)
(C) Thickness of spacers
- 9N-6496 Spacer ... 4.115 ± 0.013 mm (0.1620 ± 0.0005 inch)
- 9N-6495 Spacer ... 4.216 ± 0.013 mm (0.1660 ± 0.0005 inch)
- 5M-2697 Spacer ... 4.318 ± 0.013 mm (0.1700 ± 0.0005 inch)
- 2M-4208 Spacer ... 4.420 ± 0.013 mm (0.1740 ± 0.0005 inch)
- 2M-4209 Spacer ... 4.521 ± 0.013 mm (0.1780 ± 0.0005 inch)
- 2M-4210 Spacer ... 4.623 ± 0.013 mm (0.1820 ± 0.0005 inch)
- 2M-4211 Spacer ... 4.724 ± 0.013 mm (0.1860 ± 0.0005 inch)
- 2M-4212 Spacer ... 4.826 ± 0.013 mm (0.1900 ± 0.0005 inch)
- 5M-2691 Spacer ... 4.928 ± 0.013 mm (0.1940 ± 0.0005 inch)
- 5S-7189 Spacer ... 5.029 ± 0.013 mm (0.1980 ± 0.0005 inch)
- 9N-6495 Spacer ... 4.216 ± 0.013 mm (0.1660 ± 0.0005 inch)
(D) Dimensions for the fuel injection pump plunger
- Length of a new fuel injection pump plunger ... 69.118 ± 0.013 mm (2.7212 ± 0.0005 inch)
- Minimum length of a fuel injection pump plunger that may be reused ... 69.079 mm (2.7196 inch)
(E) Dimensions for the fuel rack
- Diameter of a new fuel rack ... 12.662 ± 0.005 mm (0.4985 ± 0.0002 inch)
- Bearing bore in the front of the pump housing after installation of the bearing ... 12.758 ± 0.038 mm (0.5023 ± 0.0015 inch)
- Bore in the rear of a new pump housing ... 12.758 ± 0.046 mm (0.5023 ± 0.0018 inch)
- Maximum clearance between a fuel rack and bearings that are worn ... 0.18 mm (0.007 inch)
- Bearing bore in the front of the pump housing after installation of the bearing ... 12.758 ± 0.038 mm (0.5023 ± 0.0015 inch)
(F) Camshaft bearing journals
- Bore in the camshaft bearing after installation into the fuel pump housing ... 53.988 ± 0.038 mm (2.1255 ± 0.0015 inch)
- Diameter of the camshaft bearing journals ... 53.899 ± 0.013 mm (2.1220 ± 0.0005 inch)
- Maximum clearance between a camshaft and bearings that are worn ... 0.25 mm (0.010 inch)
- Diameter of the camshaft bearing journals ... 53.899 ± 0.013 mm (2.1220 ± 0.0005 inch)
Show/hide table
Illustration 3 | g01394217 |
Note: Install the correct spacer thickness (G) in order to obtain the necessary timing dimension (H) .
(8) Use the 5P-4158 Gauge (Fuel Injection Timing) to measure the timing dimension.
- Timing dimension with the pump on the engine ... 106.487 ± 0.051 mm (4.1924 ± 0.0020 inch)
- Timing dimension for bench test ... 110.335 ± 0.013 mm (4.3439 ± 0.0005 inch)
Caterpillar Information System:
AccuGrade® GPS (CD700) Receiver Configuration
2007/06/25 New O-Rings are Used {1307, 7555}
C15 Generator Set Engines Engine Pressure Sensor Open or Short Circuit - Test
2007/05/21 New Procedure to Seal Planetary Tie Bolts to the Transmission Housing is Now Used {3160}
Proper Marking of the Ground Connections{4459} Proper Marking of the Ground Connections{4459}
C15 On-Highway Engine Flame Detection Temperature Sensor - Remove and Install
C15 On-Highway Engine Turbocharger Outlet Temperature Sensor - Remove and Install
C15 Generator Set Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
C15 On-Highway Engine Compression Brake
3408B and 3408C Industrial and Marine Engines Auxiliary Water Pump
C6.6 Engines for Caterpillar Built Machines Electronic Unit Injector - Install
320 Variable Gauge OEM Undercarriage Safety Messages
3408B and 3408C Industrial and Marine Engines Flywheel
C9 On-highway Engine Clean Gas Induction Cooler
C32 Marine Propulsion Engines Fuel Level - Test
Installation of New Injector Sleeve O-Ring Seals{1100, 1125} Installation of New Injector Sleeve O-Ring Seals{1100, 1125}
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 2999 - FMI 02
AccuGrade® GPS (CD700) Wireless Communication
AccuGrade® GPS (CD700) System Schematic
AccuGrade® GPS (CD700) Software Support Option
C15 On-Highway Engine Air Pump (ARD Purge) - Remove
AccuGrade® GPS (CD700) Root Folder
AccuGrade® GPS (CD700) Operator Access
AccuGrade® GPS (CD700) On-Grade Tolerance