Battery Problem
- Charging circuit
- Batteries
- Auxiliary device
Complete the procedure in the order in which the steps are listed.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Charging Circuit A. Check that the battery charging circuit is operating correctly. Refer to Troubleshooting, "Alternator Problem". |
Charging circuit |
Result: The charging circuit is not OK. Repair: Repair the charging circuit, as necessary. Result: The charging circuit is OK. Proceed to Test Step 2. |
2. Batteries A. Verify that the battery or batteries are no longer able to hold a charge. Refer to Systems Operation/Testing and Adjusting, "Battery - Test". |
Battery |
Result: One of the batteries is not OK. Repair: Replace the faulty battery. Refer to the Operation and Maintenance Manual. Result: The battery or batteries are OK. Proceed to Test Step 3. |
3. Auxiliary Device A. Check if an auxiliary device has drained the battery or batteries by being left in the ON position. |
Auxiliary Device |
Result: The battery or batteries have been drained by an auxiliary device being left in the ON position. Repair: Charge the battery or batteries. Verify that the battery or batteries are able to maintain a charge. Refer to Systems Operation/Testing and Adjusting for the correct procedure. Result: The battery or batteries have not been drained by an auxiliary device being left in the ON position. Contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
C4.4 and C7.1 Engines Alternator Problem - Charging Problem and/or Noisy Operation
C3.4B Engines for Caterpillar Built Machines Support and Mounting (CEM) - Remove and Install - Flywheel Housing Mounted CEM
C3.4B Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install - Nitrogen Oxide Sensor on Engine
C3.4B Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Tank - Remove and Install
C3.4B Engines for Caterpillar Built Machines DEF Injector and Mounting - Remove and Install
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Lines - Remove and Install
C7.1 Engines Acceleration Is Poor or Throttle Response Is Poor
320D2 Forest Machine Machine System Specifications Solenoid Valve
335F CR Excavator Machine Systems Gear Pump (Auxiliary) - Remove and Install
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Sensor Signal (Analog, Passive) - Test
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Sensor Signal (PWM) - Test
2014/12/10 Improved Power Train Software Is Now Available for Certain 990H Wheel Loader {4269, 5737, 7620}
2015/04/01 An Improved Power Train Hose Assembly Is Now Used On Certain D8T Track-Type Tractors {3016}
2015/01/06 Improved Securing of Tilt Harness for Certain Medium Wheel Loaders {1408}
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Sensor Supply - Test
Supplemental Service Information for the USAF 980H Rough Terrain Forklift {0374, 7000} Supplemental Service Information for the USAF 980H Rough Terrain Forklift {0374, 7000}
2014/11/27 New Anti - Drift Valve Logic Element Is Now Used On Certain Medium Wheel Loaders {5067}
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Solenoid Valve - Test
2014/12/18 A New Check Valve and Pressure Sensors Are Used on Certain Tier 4 Interim Machine Engines {1439}
335F CR Excavator Machine Systems Swing Motor - Disassemble
335F CR Excavator Machine Systems Swing Motor - Assemble