Electric Starting Motor
Show/hide table
Illustration 1 | g01330621 |
Show/hide table
Illustration 2 | g01330624 |
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... Clockwise
No load conditions at
- Minimum speed with no load ... 6900 ± 1800 rpm
- Maximum current with no load ... 150.5 ± 27.5 amp
- Voltage ... 11 V
- Maximum current with no load ... 150.5 ± 27.5 amp
(1) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Battery terminal
- Maximum number of cable or wire terminals between the nuts ... 3
- Tighten the nut on the battery terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft) - Tighten the nut on the battery terminal to the following torque. ...
(3) Starter relay terminal
- Tighten the nut on the starter relay terminal to the following torque. ...
1.7 ± 0.25 N·m (15 ± 2 lb in)
(4) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
2.25 ± 0.25 N·m (20 ± 2 lb in)
(5) Switch terminal
- Tighten the nut on the switch terminal to the following torque. ...
2.25 ± 0.25 N·m (20 ± 2 lb in)
Note: The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use molded terminals.
(6) Motor frame terminal
- Tighten the nut on the motor frame terminal to the following torque. ...
8 ± 3 N·m (70 ± 27 lb in)
(7) Motor terminal
- Tighten the nut on the motor terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
Current draw at 10 V and
- Pull-in windings ... 97 Amp
- Hold-in windings ... 18 Amp maximum
Caterpillar Information System:
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 00
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1627 FMI 03
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 12
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 08
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 04
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 03
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 02
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 0342 FMI 02
C9.3 Industrial Engine Electric Starting Motor
3408E and 3412E Engines for Caterpillar Built Machines Fuel Filter Base
C175-16 and C175-20 Engines for Caterpillar Built Machines Air Compressor - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Fuel Injector Oil Leakage - Check
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 02
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 03
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 04
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 05
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 07
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 08
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 09
VR6 Voltage Regulator Electrical
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines CID 1684 FMI 10
3500B Marine Propulsion Engines Speed Sensor - Clean/Inspect
VR6 Voltage Regulator Dimensions
784C and 785C Off-Highway Truck/Tractors Rim - Inspect