Nozzle Heater Harness - Remove and Install
Removal Procedure
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Open the hood.
- Cut cable straps (2) from harness assembly (1) .
Note: Note position of cable straps.
Show/hide table
Illustration 1 | g02029533 |
- Slide the locking tab for connection (3) into the unlocked position.
- Disconnect harness assembly (1) from connection (3) .
- Make temporary marks on heated nozzle connection (6) and the combustion head for the ARD for installation purposes.
Show/hide table
Illustration 2 | g02029535 |
- Remove allen head screw (5) and clamp (4) .
- Remove heated nozzle connection (6) from the combustion head for the ARD.
- Remove O-ring seals (8) and O-ring seal (7) from the heated nozzle.
Show/hide table
Illustration 3 | g02029536 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 247-5377     | Torque Wrench     | 1     |
- Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
- Install new O-ring seals (8) and O-ring seal (7) to heated nozzle connection (6) .
Show/hide table
Illustration 4 | g02029536 |
Show/hide table
Illustration 5 | g02029535 |
- Position harness assembly (1) and install heated nozzle connection (6) to the combustion head for the ARD.
Note: Ensure correct orientation of the heated nozzle connection.
- Install clamp (4) and allen head screw (5) .
- Use Tooling (A) in order to tighten the allen head screw to a torque of 1.7 N·m (15 lb in).
- Connect harness assembly (1) to connection (3) .
Show/hide table
Illustration 6 | g02029533 |
- Slide the locking tab for connection (3) into the locked position.
- Install new cable straps (2) to harness assembly (1) .
Note: Ensure that cable straps meet the Original Equipment Manufacturers (OEM) specification.
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump
C6.6 Engines for Caterpillar Built Machines Fuel Injection Nozzles
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump
950K and 962K Wheel Loaders C7.1 Engine Supplement Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
950K and 962K Wheel Loaders C7.1 Engine Supplement Unit Injector - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines
950K and 962K Wheel Loaders C7.1 Engine Supplement Soot Sensor - Remove and Install
992K Wheel Loader Electrohydraulic System Check Valve
950K and 962K Wheel Loaders C7.1 Engine Supplement Unit Injector - Remove
992K Wheel Loader Electrohydraulic System Piston Pump (Hydraulic Fan)
950K and 962K Wheel Loaders C7.1 Engine Supplement Pressure Sensor (DPF) - Remove and Install - Clean Emissions Module
950K and 962K Wheel Loaders C7.1 Engine Supplement Hood - Remove and Install
950K and 962K Wheel Loaders C7.1 Engine Supplement Unit Injector Hydraulic Pump - Remove
950K and 962K Wheel Loaders C7.1 Engine Supplement Diesel Particulate Filter - Remove
950K and 962K Wheel Loaders C7.1 Engine Supplement Unit Injector Hydraulic Pump - Install
950K and 962K Wheel Loaders C7.1 Engine Supplement Diesel Particulate Filter - Install
992K Wheel Loader Electrohydraulic System MID 082 - CID 0262 - FMI 03
621H, 623H and 627H Wheel Tractor-Scrapers Power Train Transmission, Torque Converter, Transfer Gears and Differential - Remove and Install - Tractor
621H, 623H and 627H Wheel Tractor-Scrapers Power Train Transmission, Torque Converter, Transfer Gears - Remove and Install - Tractor
992K Wheel Loader Electrohydraulic System MID 082 - CID 0262 - FMI 04
D6K2 Track-Type Tractor Systems Piston Pump Neutral (Winch) - Test and Adjust
924K, 930K and 938K Wheel Loaders Electrohydraulic System General Information (Power Train System)
D11R Track-Type Tractor Maintenance Interval Schedule
950M, 962M, 950M Z and 962M Z Wheel Loaders Engine Oil Filter and Oil Filter Base - Remove and Install