1. Home
  2. Caterpillar
  3. Testing and Adjusting
  4. #i04502214

992K Wheel Loader Electrohydraulic System Caterpillar


Position Sensor (Tilt Linkage) - Replace

Usage:

992K 880

  • Tilt the bucket to a position level with the ground. Lower the bucket to the ground.

  • Connect the steering frame lock link.

  • Engage the parking brake.

  • Stop the engine and leave the key start switch in the OFF position.
    Show/hide table
    Illustration 1g01618533
    Right Side of Lift arm Crossmember
    (1) Tilt linkage position sensor

  • Remove the outer cover plate. Disconnect the harness connector from the sensor connector.

  • Remove the bracket from the lift arm.

  • Remove the lever from the Tilt Linkage Position Sensor.

  • Remove the Tilt Linkage Position Sensor from the bracket.

    Show/hide table
    NOTICE

    The position sensor can be damaged if too much force is applied against the internal stops of the sensor. Be careful when removing the position sensor lever or rotating the shaft attached to the sensor.

  • Install the new Tilt Linkage Position Sensor on the bracket.

  • Install the lever on the new Tilt Linkage Position Sensor.

  • Install the bracket on the lift arm crossmember.

  • Connect the harness connector to the sensor connector. Install the outer cover plate.

  • The Tilt Linkage Position Sensor must be calibrated before the machine is returned to use.

    Reference: For the correct procedure in order to calibrate the Tilt Linkage Position Sensor, refer to Testing and Adjusting, KENR7579, "992K Wheel Loader Electrohydraulic System", "Tilt Linkage Position Sensor Calibration".

    • Caterpillar Information System:

    992K Wheel Loader Electrohydraulic System Position Sensor (Lift Linkage) - Replace
    950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3470 - FMI 05
    950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3470 - FMI 03
    992K Wheel Loader and 854K Wheel Dozer Power Train Oscillating Axle (Rear)
    950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3467 - FMI 05
    950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3467 - FMI 03
    D6T LGP (OEM) Maintenance Interval Schedule
    950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3071 - FMI 06
    992K Wheel Loader and 854K Wheel Dozer Power Train Fixed Axle (Front)
    950K Wheel Loader and 962K Wheel Loader Steering System Piston Pump (Steering)
    950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3071 - FMI 05
    992K Wheel Loader and 854K Wheel Dozer Power Train Differential and Bevel Gear
    992K Wheel Loader and 854K Wheel Dozer Power Train Final Drive, Brake and Wheel
    992K Wheel Loader and 854K Wheel Dozer Power Train Rim Mounting
    992K Wheel Loader and 854K Wheel Dozer Power Train Control Manifold (Axle Oil Cooler)
    992K Wheel Loader Secondary Steering - Test
    D3K2, D4K2 and D5K2 Track-Type Tractors Machine Systems Floorplate
    992K Wheel Loader and 854K Wheel Dozer Power Train Axle Oil Cooler Pump and Motor
    D9T Track-Type Tractor Engine Supplement Engine Oil Pump - Remove
    D6T LGP (OEM) Safety Messages
    992K Wheel Loader and 854K Wheel Dozer Power Train Oil Filter (Axle Oil Cooler)
    D9T Track-Type Tractor Engine Supplement Engine Oil Pump - Install
    950K Wheel Loader and 962K Wheel Loader Steering System Metering Pump (HMU Steering)
    D9T Track-Type Tractor Engine Supplement Engine Oil Pan - Remove and Install
    Back to top
    Contacts My AVS
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.