Track - Adjust
步骤
Show/hide table
润滑脂有很高的压力。 润滑脂在压力下喷出卸压阀能够穿透身体,造成伤亡。 不要通过泄压阀来观察润滑脂是否溢出。 应观察履带或履带调整油缸来查看履带是否松动。 只要转一圈,以便把卸压阀松开。 |
向前移动机器。 在不使用行车制动器的情况下让机器停止。 当机器处于一般工作状态时,调整履带。 如果工作场所填料较多,则应在带有填料的情况下来调节履带。
Show/hide table
图 1 | g00040329 |
如果机器没有托链轮,则要测量链轮和前引导轮之间的履带是否松弛。 尺寸 (2) 的正确调整值应为 130 ± 10 mm (5.1 ± 0.4 in)。
Show/hide table
图 2 | g00104000 |
如果机器配备有托链轮,则应计算尺寸 (3) 和尺寸 (4) 的和。 和等于 130 ± 10 mm (5.1 ± 0.4 in) 时即可获得正确的下垂度。
松弛履带的调整
Show/hide table
图 3 | g00680166 |
Show/hide table
注意 |
---|
当尺寸 (1) 为 150 mm (5.9 in) 或以上时不要试图拧紧履带。 联系您的 Caterpillar 代理商了解履带维修或相关说明。 |
- 卸下检修盖。
- 通过履带调整阀 (5) 加入多功能润滑脂 (MPGM)。 添加MPGM直到尺寸 (2) 正确。
Show/hide table
图 4 | g00689385 |
- 向前及向后操作机器,以使压力平衡。 让机器滑行直到完全停止。 不要使用制动器。
- 重新测量尺寸 (2) 。 重复步骤2 和 5,直到尺寸 (2) 正确为止。
- 安装检修盖。
绷紧履带的调整
- 卸下检修盖。
- 通过旋转 360 度来拧松安全阀 (6) 。 让润滑脂流出。
Show/hide table
图 5 | g00689386 |
- 关闭安全阀。
- 通过履带调整阀 (5) 加入多用途润滑脂(MPGM)。 添加润滑脂直到尺寸 (2) 正确。
- 向前及向后操作机器,以使压力平衡。 让机器滑行直到完全停止。 不要使用制动器。
- 重新测量尺寸 (2) 。 重复步骤4 和 5,直到尺寸 (2) 正确为止。
- 安装检修盖。
Caterpillar Information System:
966M and 972M Wheel Loaders Stopping the Machine
D7E Track-Type Tractor Hydraulic, HVAC and Electrical Systems Accumulator (Pilot) - Test and Charge
966M and 972M Wheel Loaders Operator Station
966M and 972M Wheel Loaders Work Tools
966M and 972M Wheel Loaders Operation
541 Series 2 and 552 Series 2 Track Feller Bunchers Fire Extinguisher Location
992K Wheel Loader Machine Systems Window Wiper and Wiper Motor (Rear) - Remove and Install
D9T Track-Type Tractor Power Train Brake Pressure - Test
C9.3 Marine Generator Set Engines Cooling System - Inspect
C13 Industrial Engine Engine Air Cleaner Element (Single Element/Canister Type) - Clean/Replace - If Equipped
C7.1 Industrial Engine Engine Air Cleaner Element (Dual Element/Canister Type) - Clean/Replace - If Equipped
D7E Track-Type Tractor Hydraulic, HVAC and Electrical Systems Piston Pump (Steering Charge and Pilot Pressure) - Test and Adjust
950K and 962K Wheel Loaders Automatic Lubrication Grease Tank - Fill - Autolube - If Equipped
2011/10/07 Improved Angle Cylinder Now Used on Certain D6N Track Type Tractors {5101}
C4.4 Industrial Engine Atmospheric Pressure Sensor
C4.4 Industrial Engine Electronic Control Module
950K and 962K Wheel Loaders Radiator Core - Clean
621H, 623H and 627H Wheel Tractor-Scrapers Hydraulic and Steering System General Information
C11 and C13 Industrial Engines Engine Oil Level - Check
C9.3 Engines for Caterpillar Built Machines Engine Shutdown Occurs Intermittently
D8T Track-Type Tractor Hydraulic System Bank Valve (Five)
C9.3 Engines for Caterpillar Built Machines Exhaust System Contains Oil
C9.3 Engines for Caterpillar Built Machines ECM - Replace
D9T Track-Type Tractor Systems Torque Converter and Housing