TA19-M2WD and TA19-M4WD Agricultural Transmissions Caterpillar

Transmission Oil Sample - Obtain

Usage:

Show/hide table

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.

The oil sampling valve for the transmission oil may be located in-line on the inlet side of the transmission. If your transmission does not have an oil sampling valve, contact your Caterpillar dealer for the appropriate hardware and for the instructions in order to install the oil sampling valve.

The oil filters are mounted remotely from the transmission. The mounting locations will vary between Original Equipment Manufacturers.

Refer to Special Publication, PEHP6001, "How To Take A Good Oil Sample". Also, refer to Operation and Maintenance Manual, "S·O·S Information" and Special Publication, SEBU6250, "S·O·S Oil Analysis" for additional information about obtaining an oil sample.

Caterpillar Information System:

UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Transformer (Maintenance Bypass Cabinet)

UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Time Delay Relay

2006/06/01 New Connecting Rod and Main Bearings {1203, 1218, 1230}

UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Remote Input/Output Dry Contact - Setup

2006/05/29 Radiator pedestal on 1104C-TAG engines: Smaller engine mounting holes for improved accuracy of the fan position in the radiator cowl. {1353}

UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Maintenance Power Supply PWA

C7 and C9 On-Highway Engines Engine Monitoring Parameters

UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Ethernet - Configure

2006/06/01 Do Not Reuse the Hold Down Bolts for the Fuel Injector {1290}

2014/08/14 Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}

2006/05/29 Do Not Reuse the Hold Down Bolts for the Fuel Injector {1290}

C4.4 Industrial Engine Air Inlet and Exhaust System - Inspect

UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Cable Landing (Maintenance Bypass Cabinet)

C9 Engine for Caterpillar Built Machines Camshaft - Remove

UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Emergency Power Off - Reset

UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Remote Notification - Setup

C9 Engine for Caterpillar Built Machines Camshaft - Install

UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Circuit Breaker (Maintenance Bypass Cabinet)

TA22-4WD Agricultural Transmission Capacities (Refill)

2006/05/22 Revised Product Support Update {0374}

C4.4 Industrial Engine Alternator - Test

C4.4 Industrial Engine Crankshaft Pulley - Check

UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Modem - Configure

UPS 1000S/ UPS 1200S Uninterruptible Power Supplys General Information (Input/Output Cabinet)