STIC Control - Install
Installation Procedure
- Install the STIC steering control lever and the steering pilot valve as a unit.
Show/hide table
Illustration 1 | g00392414 |
Typical Example |
- Connect hydraulic control lock (17) to the steering pilot valve.
Note: Make sure that the spring is in the back of the hydraulic control lock.
- Install spacers (18), the washers and three bolts (16) .
- Connect four hose assemblies (15) .
Show/hide table
Illustration 2 | g00392413 |
Typical Example |
- Connect two electrical connectors (14). Install three cable ties (13) .
Show/hide table
Illustration 3 | g00392412 |
Typical Example |
- Install housing (9) and screws (10) .
Show/hide table
Illustration 4 | g00392411 |
Typical Example |
- Install nut (11) and knob (12). Tighten nut (11) .
- Install housing (8) and eleven screws (7) .
Show/hide table
Illustration 5 | g00392410 |
Typical Example |
- Install lock knob (5). Tighten nut (6) .
- Install guard assembly (3) and four screws (4) .
Show/hide table
Illustration 6 | g00392408 |
Typical Example |
- Lift handle (2) and close lid (1) .
Show/hide table
Illustration 7 | g00392407 |
Typical Example |
- Check the oil level in the hydraulic tank for the steering system and for the braking system. For the correct procedure, refer to the Operation and Maintenance Manual for your machine.
- Start the engine and check for leaks.
- Separate the steering frame lock. Refer to Disassembly and Assembly Manual, "Steering Frame Lock - Separate and Connect".
Note: After the steering frame lock is separated, check for proper operation of the steering system.
Caterpillar Information System:
D6R Track-Type Tractor Capacities (Refill)
Corrosion Protection Package for Certain Wheel Loader Machines{0645, 1000, 7000, 7559} Corrosion Protection Package for Certain Wheel Loader Machines{0645, 1000, 7000, 7559}
Measuring Bores and Installing Seals in Standard and Oversized Hydraulic Cylinders {5100, 7562} Measuring Bores and Installing Seals in Standard and Oversized Hydraulic Cylinders {5100, 7562}
C9 Engine and D7E Track-Type Tractors Engine Does Not Crank
D6N Track-Type Tractor Reference Material
657G Wheel Tractor-Scraper Maintenance Interval Schedule
2008/09/08 Improved Metering Pump For Compact Wheel Loaders {4312}
3500 Generator Sets Generator Operation
D7R Track-Type Bulldozer Stopping the Engine
D7R Track-Type Bulldozer Stopping the Machine
994F and 994H Wheel Loaders Automatic Lubrication System Automatic Lubrication System - Maintenance
993K Wheel Loader Machine Systems Piston Pump (Implement Pilot) (Axle Oil Cooler) - Disassemble
988F and 988F Series II Wheel Loaders Power Train Fixed Axle (Front) - Install
988F and 988F Series II Wheel Loaders Power Train Oscillating Axle (Rear) - Install
D6R Track-Type Tractor Braking System - Test
988F and 988F Series II Wheel Loaders Power Train Oscillating Axle (Rear) - Install
Medium Wheel Loader Series H Definitions of Configuration Parameters for Transmission, Engine and Implement Electronic Control Modules{1901, 1920, 4800, 7610, 7620} Medium Wheel Loader Series H Definitions of Configuration Parameters for Transmission, Engine and Implement Electronic Control Modules{1901, 1920, 4800, 7610, 7620}
993K Wheel Loader Machine Systems Selector and Pressure Control Valve (Secondary Steering) - Disassemble
D6R Track-Type Tractor Fuel Tank Cap Filter and Strainer - Replace/Clean
Custom Product Support Literature for the 980H Wheel Loaders that have a 331-9944 Steel Mill Arrangement {0374, 7000} Custom Product Support Literature for the 980H Wheel Loaders that have a 331-9944 Steel Mill Arrangement {0374, 7000}
C9.3 Engine for Caterpillar Built Machines Fuel Injector
613G Wheel Tractor-Scraper Power Train Axle Mounting
613G Wheel Tractor-Scraper Power Train Drive Shaft
613G Wheel Tractor-Scraper Power Train Differential Lock