Bench Test Procedure for Hydraulic Piston Pumps {4306, 5070, 5084} Caterpillar

Integrated Toolcarrier

IT38H (S/N: JNJ1-UP)

IT62H (S/N: M5G1-UP)

Wheel Loader

938H (S/N: MCC1-UP; MJC1-UP; JKM1-UP; LKM1-UP)

950H (S/N: N1A1-UP; JAD1-UP; M1G1-UP; J5J1-UP; K5K1-UP)

950K (S/N: R4A1-UP; J5M1-UP; FER1-UP)

950L (S/N: TNS1-UP)

950M (S/N: EMB1-UP; ENE1-UP; NHL1-UP; FTR1-UP; LCR1-UP; J1S1-UP)

950M Z (S/N: HE81-UP)

962H (S/N: N4A1-UP; M3G1-UP; J6J1-UP; K6K1-UP; MAL1-UP)

962K (S/N: T6A1-UP; FLL1-UP; X4T1-UP)

962L (S/N: MTN1-UP; SXS1-UP)

962M (S/N: K881-UP; EJB1-UP; LSE1-UP; RCL1-UP; J2S1-UP; F2T1-UP)

962M Z (S/N: SA81-UP)

966H (S/N: BJ61-UP; BS61-UP; A6D1-UP; RYF1-UP; A6G1-UP; A6J1-UP; TAL1-UP; FMW1-UP)

966L (S/N: FSL1-UP; FRS1-UP)

966M (S/N: MD71-UP; EJA1-UP; DYC1-UP; R8D1-UP; LMM1-UP; KJP1-UP; L8R1-UP)

966M Series XE (S/N: DZL1-UP)

972H (S/N: GTA1-UP; LCC1-UP; A7D1-UP; NPE1-UP; A7G1-342,433-UP; WXZ1-UP)

972L (S/N: RFB1-UP)

972M (S/N: L8E1-UP; LSJ1-UP; GGN1-UP; WGN1-UP; A8P1-UP; JPR1-UP; M8W1-UP)

Introduction

© 2018 Caterpillar All Rights Reserved. This guideline is for the use of Caterpillar Dealers only. Unauthorized use of this document or the proprietary processes therein without permission may be violation of intellectual property law. Information contained in this document is considered Caterpillar: Confidential Yellow.

This Special Instruction includes test procedures for piston pumps. This Special Instruction also provides specifications. The technician should have a good understanding of hydraulic piston pumps. The technician should be educated in the operation of the hydraulic test bench. The test benches in this document are available through the Caterpillar Service Tool Division. Gather all necessary tooling before you need to hook up the pump. Some of the required tooling appears in a table at the end of this document. There are many possible variations of tooling that could be used. Not every possible variation can be listed.

For technical questions when using this document, work with your Dealer Technical Communicator (TC).

To report suspected errors, inaccuracies, or suggestions regarding the document, submit a form for feedback in the Service Information System (SIS Web) interface.

Canceled Part Numbers and Replaced Part Numbers

This document may not include all Canceled part numbers and replaced part numbers. Use NPR on SIS for information about Canceled part numbers and replaced part numbers. NPR will provide the current part numbers for replaced parts.

Safety

Illustration 1	g02139237

Show/hide table

Personal injury or death can result from improperly checking for a leak. Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.

Show/hide table

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

Show/hide table

Pump test pressures in this guideline may exceed the normal operating range of the hydraulic test hoses utilized when connecting the tested pump to the test bench. However, the order of magnitude of these pressures is significantly below the burst strength of the Caterpillar "XT6" product. High pressure oil can escape through improperly assembled hoses and fittings. High pressure oil can also escape through poorly maintained hoses and fittings. High pressure oil may also leak through hose that has become damaged over the life of the hose due to the pressure levels that occur during test bench operation. Personal injury or death can result from improper hose & fitting inspection or improper hose replacement procedures. Escaping fluid under pressure can penetrate body tissue causing serious injury, and possible death. Thoroughly inspect all testing hoses, fittings, and quick disconnects prior to any testing operation. Check the assembly date tag or hose assembly log date for a hose life indicator. Replace all Test Bench hoses at a minimum of every 2 years or earlier if the hose or fittings appear to be damaged.

Summary

This procedure is specific to the type of pump and the type of control. Refer to the test specifications and the tooling at the end of this document.

Note: A paper copy of this document may not be the latest version. Go to the Service Information System (SIS) to view the latest version.

References

Connections for the Caterpillar Hydraulic Test Center

Illustration 2	g01063311
Connections for the test center (1) Flow control for discharge (2) "F3" flow meter inlet (3) "F4" flow meter inlet (4) Oil supply from the auxiliary pump (5) "F3" inlet for the flow meter with flow limiter (6) "F3"outlet for the flow meter with pressure control (7) Load sensing pressure (8) Signal pressure (9) "F4" outlet for the flow meter (10) Return to tank (11) Connections for case drain (12) Oil supply

Illustration 3	g01063312
Control and Gauges for the test center (13) Meter for speed and torque (14) Gauge for signal pressure (15) Control for signal pressure (16) Pressure gauge for auxiliary pump (17) Auxiliary pump flow (18) "F3" discharge pressure gauge (19) "F3" discharge flow (20) "F4" discharge pressure gauge (21) "F4" discharge flow (22) Auxiliary pump flow control (23) "F3" margin pressure (24) "F3" Load control for discharge pressure (25) "F4" Load control for discharge pressure

Connections for the Caterpillar Hydraulic Test Bench

Illustration 4	g01063314
Connections for the test bench (26) "Flow meter 1" loop and "Flow meter 2" loop (27) Oil supply

Illustration 5	g01093468
Connections for the test bench (28) "Flow meter 2" loop (29) "Flow meter 1" loop (30) "Flow meter 2" outlet (31) Signal pressure line (32) "Flow meter 2" inlet (33a) "Flow meter 1" outlet (33b) Outlet for the auxiliary oil supply (34) Inlet for the auxiliary oil supply (35) "Flow meter 1" inlet

Illustration 6	g01063316
Control and Gauges for the test bench (36) Supply pressure for the auxiliary oil (37) Signal pressure (38) Control for signal pressure (39) "Flow meter 1" discharge pressure (40) Control for auxiliary oil supply pressure (41) "Flow meter 2" discharge pressure (42) Control for the auxiliary oil supply (43) "Flow meter 2" discharge flow (44) Discharge flow for auxiliary pump (45) "Flow meter 1" discharge flow (46) "Flow meter 1" load control (47) Speed and direction control (48) "Flow meter 2" load control

Port Locations

Illustration 7	g01401279
Typical port locations and adjustments (49) Suction port (50) Discharge port (51) Adjustment screw for maximum displacement (52) Case drain port (53) Pressure port for load sensing (54) Adjustment screw for margin pressure (55) Adjustment screw for margin control valve sleeve

Illustration 8	g01346146
Hydraulic Schematic (49) Suction port (50) Discharge port (52) Case drain port (53) Pressure port for load sensing

4C-3582 Load Sensing Valve

Illustration 9	g01401294
4C-3582 Load Sensing Valve

Illustration 10	g01401299
4C-3582 Load Sensing Valve

Illustration 11	g01401304
Schematic for 4C-3582 Load Sensing Valve (56) Outlet port (57) Adjustment for the discharge flow (58) Inlet port (59) High-pressure port (60) Adjustment for the discharge pressure (61) Low-pressure port (62) Pressure port for the load sensing

Illustration 12	g01401309
4C-3582 Load Sensing Valve and 1U-5796 Pressure Differential Gauge (56) Line to the flow meter on the test bench (57) Adjustment knob for discharge flow (58) Line from the pump discharge port (59) To the high side of the differential gauge (60) Load control for pump discharge pressure (61) Line to the low side of the differential gauge (62) Pressure port for load sensing (63) Pressure differential gauge group (64) Line to the low side of the load sensing group (65) Line to the high side of the load sensing group

Pump Setup

1. Connect the suction port (49) to the oil supply on the test bench.

2. Connect a one inch high-pressure "XT6" hose from the pump discharge port (50) to inlet port (58) on the 4C-3582 Load Sensing Valve.

3. Connect a one inch high-pressure "XT6" hose from outlet port (56) on the 4C-3582 Load Sensing Valve to the flow meter inlet on the test bench.

4. Connect a one inch high-pressure hose from the flow meter outlet on the test bench back to the tank.

5. Connect a 6D-7726 Hose Assembly to the pressure port for load sensing (62). Connect the other end of 6D-7726 Hose Assembly to the pressure port for load sensing (53) on the pump.

   Note: Do not use 1U-5754 Hose Assembly or 1U-5755 Hose Assembly for load sensing signal lines. The flow rate through these hoses will not compensate for the possible leakage through the control valve. Erratic readings will result.

6. Connect the 1U-5796 Pressure Differential Gauge Group (63) to the high-pressure valve port (59) and low-pressure valve port (61) on the 4C-3582 Load Sensing Valve. The port marked "hi" (65) on the 1U-5796 Pressure Differential Gauge Group should be hooked up to the port marked "hi" (59) on the 4C-3582 Load Sensing Valve. The port marked "low" (64) on the 1U-5796 Pressure Differential Gauge Group should be hooked up to the port marked "low" (61) on the 4C-3582 Load Sensing Valve.

   Note: The 4C-3582 Load Sensing Valve will only be used in Step 3 of the Test Procedure.

   Note: The ports marked "low" (61) and "sense line" (62) on the 4C-3582 Load Sensing Valve are reading the same pressure.

7. Purge all air from the suction line. Loosen the suction hose at the pump until oil leaks from the connection. Tighten the suction hose.

8. Fill the pump case with oil. Pour oil directly into a case drain port until the case is completely full.

9. Connect an in-line flow meter to the case drain port (52). Direct the oil from the in-line flow meter back to the tank.

10. Do not rotate the pump in the wrong direction. The correct direction of rotation will be stated on the pump. The correct direction of rotation will also be in the test specifications. The direction of rotation is viewed from the input shaft end. Visually check the pump for proper rotation.

Test Procedure

Note: The steps in the procedure correlate with the steps under the test specifications according to your specific part number.

The contamination level of the hydraulic oil in the test bench should be ISO 16/13 or better. The oil in the test bench should be one of the following.

• SAE 10W at 50 °C (122 °F) or

• Mobil DTE-11 at 46 °C (115 °F)

1. Start rotating the pump according to the rpm in Step 1 of the Test Specifications. Listen for abnormal noise. Verify flow from the pump. Verify that all connections are tight. Check for leaks around shaft seals. Check for leaks around the control valve.

   Run the pump for at least five minutes to raise the temperature of the oil and purge the system of air.

2. Slowly increase the input rpm to the value in Step 2 of the Test Specifications. Adjust the discharge pressure to the value listed in step 2 of the Test Specifications. If the actual flow is less than the value in Step 2 of the Test Specifications, the pump may not be mechanically feasible. The pump should be internally inspected.

   Note: Verify adjustment screw (55) is bottomed out before adjusting margin pressure.

   Note: The 4C-3582 Load Sensing Valve will only be used in Step 3 of the Test Procedure.

3. Slowly adjust the input rpm to the value in Step 3 of the Test Specifications. Adjust the discharge pressure to the value listed in step 3 of the Test Specifications. The discharge flow is adjusted by using the 4C-3582 Load Sensing Valve. Bench circuitry will be used for flow limiting if using a 1U-9400 Test Center. Adjust the discharge flow according to the values in Step 3 of the Test Specifications. Adjust the discharge pressure according to the values in Step 3 of the Test Specifications. Adjust the screw for margin pressure (54) to the value in Step 3 of the Test Specifications. The margin pressure will be displayed on the 1U-5796 Pressure Differential Gauge (63).

   Note: The margin pressure may change as discharge pressure changes. Adjust margin pressure at Step 3 within operating conditions only.

4. Slowly adjust the input rpm to the value in Step 4 of the Test Specifications. Increase the pump discharge pressure to the value in Step 4 of the Test Specifications. This value is an indication of the efficiency. If the case drain is more than the value given in Step 4 of the Test Specifications, the pump may not be mechanically feasible. The pump should be internally inspected.

Show/hide table

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

Reduce rpm and all pressures to zero. Remove the component from the test bench. Drain the oil from the pump. Plug all of the ports.

Test Specifications

Test Bench Tooling