Turbocharger - Remove and Install
拆卸步骤
注: 清洁度是一项重要的因素。 开始进行解体步骤之前，必须彻底清洁零部件外部。 这将有助于防止脏污进入内部机构。
注: 在所有线路、软管、导线及管子组件上作出识别标记，以便于安装。 插接好所有线路、软管和管子。 这将有助于防止液体泄漏和有助于防止污染物进入系统。
- 断开管 (1) 。 拆卸管组件 (2) 。
Show/hide table
 | |
| 图 1 | g01305375 |
- 拆卸螺栓 (3) 。
Show/hide table
 | |
| 图 2 | g01305385 |
- 拆卸螺栓 (5) 。 拆卸支架 (6) 。 将支架 (6) 和滤清器总成放在一旁。 将弯头 (4) 放在远离涡轮增压器 (7) 的地方。
Show/hide table
 | |
| 图 3 | g01305393 |
- 断开软管 (8) 。
Show/hide table
 | |
| 图 4 | g01305431 |
- 拆卸螺栓 (10) 。 拆卸螺母 (9) 。 拆卸涡轮增压器 (7) 。
Show/hide table
 | |
| 图 5 | g01305408 |
安装步骤
注: 清洁度是一项重要的因素。 组装之前，应使用清洗剂彻底清洁所有零部件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上，从而可能导致以后出现故障。 检验所有零件。 如果任何零件磨损或损坏，则应使用新件更换。
- 定位涡轮增压器 (7) 。 安装螺栓 (10) 。 安装螺母 (9) 。
Show/hide table
| | |
| 图 6 | g01305408 |
- 连接软管 (8) 。
Show/hide table
| | |
| 图 7 | g01305431 |
- 定位弯头 (4) 。 定位支架 (6) 和滤清器总成。 安装螺栓 (5) 。
Show/hide table
| | |
| 图 8 | g01305393 |
- 安装螺栓 (3) 。
Show/hide table
| | |
| 图 9 | g01305385 |
- 连接管 (1) 。 安装管组件 (2) 。
Show/hide table
| | |
| 图 10 | g01305375 |
Caterpillar Information System:
D3K, D4K and D5K Track-Type Tractors Electrohydraulic Power Train System Initial Pressure Tests
D6G Series II Track-Type Tractor Engine Supplement Oil Filter and Cooler Bypass Valve - Remove and Install
D7G and D7G Series II Track-Type Tractors Engine Supplement Primary Fuel Filter, Water Separator and Base - Remove and Install
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Transmission Pressures - Test and Adjust
D6N Track-Type Tractor Power Train Tracks - System One
D7G and D7G Series II Track-Type Tractors Engine Supplement Fuel Priming Pump - Remove and Install
D7G and D7G Series II Track-Type Tractors Engine Supplement Secondary Fuel Filter and Base - Remove and Install
D6T Track-Type Tractor Hydraulic System Hydraulic Tank and Filter
D7G and D7G Series II Track-Type Tractors Engine Supplement Fuel Ratio Control - Remove
D7G and D7G Series II Track-Type Tractors Engine Supplement Fuel Ratio Control - Install
Convert the AccuGrade Display Mounting from CD550 Compatible to CD700 Compatible{7220} Convert the AccuGrade Display Mounting from CD550 Compatible to CD700 Compatible{7220}
D7G and D7G Series II Track-Type Tractors Engine Supplement Alternator - Remove and Install
Bench Test Procedure for Hydraulic Piston Pumps {4306, 5070, 5084} Bench Test Procedure for Hydraulic Piston Pumps {4306, 5070, 5084}
C13, C15, and C18 Tier 4 Final Engines Variable Valve Actuator Oil Diverter Valve
D7G and D7G Series II Track-Type Tractors Engine Supplement Crankshaft Front Seal and Wear Sleeve - Remove and Install
C11 and C13 Engines and 14M and 16M Motor Graders Throttle Lock - Test
D7G2 Track-Type Tractor Hydraulic System Bulldozer Tilt Control Valve
D6N Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
D7G2 Track-Type Tractor Hydraulic System Ripper Control Valve
D7G2 Track-Type Tractor Hydraulic System Bulldozer Lift Control Valve
PL61 Pipelayer and D6K Track-Type Tractor Diagnostic Capabilities
D6N Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet) Pressure - Test and Adjust
D6T Track-Type Tractor Hydraulic System Piston Pump (Implement)
Replacement of Lift Arm Crossmembers on Wheel Loaders{6107, 6119} Replacement of Lift Arm Crossmembers on Wheel Loaders{6107, 6119}