Service Brake - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 5P-0167     | 制动器弹簧工具     | 1     |
B     | 2P-8312     | 挡圈钳     | 1     |
C     | -     | 顶出螺钉 5/8 - 11 x 4 in     |
3     |
D     | 1P-0808     | 多功能润滑脂     | -     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检验所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 安装滚柱 (18) 。 安装销组件 (17) 。 安装螺栓 (16) 。 必须正确拧紧螺栓 (16) 。 安装螺栓 (16) 的锁紧钢丝。
Show/hide table
图 1 | g01288163 |
- 安装防尘罩 (16) 。 将适当的起吊设备连接在制动鼓组件 (15) 上。 制动鼓组件 (15) 的重量约为 111 kg (245 lb)。 安置制动鼓组件 (15) 。 安装螺栓 (14) 。 拧紧螺栓 (14) 至扭矩为 120 ± 10 N·m (88 ± 7 lb ft)。 再转动螺栓 120° ± 5°。
Show/hide table
图 2 | g01287917 |
Show/hide table
图 3 | g01288365 |
- 安装滚针轴承 (13) 。 安装外轴承至深度为 7.9 ± 0.5 mm (0.31 ± 0.02 in)。 安装唇形密封 (12) 。 将工具 (C) 涂敷在唇形密封 (12) 上。 确保外侧密封唇朝向机器。 确保内侧密封唇背对机器。
Show/hide table
图 4 | g00850965 |
- 将垫圈 (11) 安装到凸轮轴 (8) 上。 将凸轮轴 (8) 安装到车轴壳体上。 安装垫圈 (10) 。 使用工具 (B) ,安装挡圈 (7) 。 安装松紧调整器 (9) 。
Show/hide table
图 5 | g01287412 |
- 需要两个人,将两个制动蹄组件 (3) 安装到车轴壳体上。 每个制动蹄组件的重量约为 45 kg (100 lb)。 安装弹簧锁和销 (6) 。
Show/hide table
图 6 | g00850962 |
- 安装螺栓 (5) 。 将锁紧钢丝 (4) 安装到螺栓 (5) 上。
- 使用工具 (A) ,安装弹簧 (2) 。 将防尘罩 (1) 安装到制动蹄组件 (3) 上。
Show/hide table
图 7 | g01287410 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
End By: 安装轮胎和车轮。 请参阅 拆解和组装, "车轮、车轮轴承和 Duo-Cone 浮式密封 - 安装"。
Caterpillar Information System:
657G Wheel Tractor-Scraper Wheel Tractor Power Train Service Brake - Remove
2006/07/17 A New Seal is Used for the Auxiliary Water Pump {1371}
2006/07/10 A New Seal is Used for the Auxiliary Water Pump {1371}
Starting and Charging Systems General Information
SystemOne Track Guiding Arrangements{4150, 4177} SystemOne Track Guiding Arrangements{4150, 4177}
525C, 535C and 545C Wheel Skidders Power Train Solenoid Valve (Transmission Clutch) - Test
2006/07/24 A New Cylinder Head Gasket is Used {1124}
2006/07/10 A Cylinder Head Gasket was Reinstated {1124}
C175-16 Locomotive Engine Aftercooler
657G Wheel Tractor-Scraper Wheel Tractor Power Train Drive Shaft - Assemble
657G Wheel Tractor-Scraper Wheel Tractor Power Train Axle Shaft - Remove and Install
657G Wheel Scraper Power Train Torque Converter - Install
Starting and Charging Systems Analyzer Test Description
Index of Repair Process Engineering Publications {0374, 1000, 7000} Index of Repair Process Engineering Publications {0374, 1000, 7000}
657G Wheel Tractor-Scraper Machine Systems Fuel Tank - Remove and Install
Starting and Charging Systems Alternator Test Description
953D Track-Type Loader Engine Supplement Muffler - Remove and Install
525C, 535C and 545C Wheel Skidders Power Train Transmission Pressures - Test and Adjust
D3K, D4K and D5K Track-Type Tractors Electrohydraulic System Relief Valve (Main) - Test and Adjust
2006/07/17 A New Valve Cover Seal is Now Used {1107, 1120}
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Steering System Metering Pump (HMU Steering)
657G Wheel Tractor-Scraper Machine Systems Bail Cylinder - Remove and Install
Starting and Charging Systems Reference Information
953D Track-Type Loader Engine Supplement Air Cleaner - Remove and Install