Piston Pump (Hydrostatic) - Disassemble - Left Side
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-1862 | 钳子 | 1 |
B | 1P-1861 | 挡圈钳 | 1 |
C | 147-8292 | 弹簧压缩器 | 1 |
D | 1U-7600 | 滑锤拉拔器总成 | 1 |
开始:
- 卸下活塞泵。 请参阅拆解和组装, "活塞泵(静液压)- 拆卸"。
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下机具和其油路之前,必须先把机具放到地面上,让油先冷却,才可进行工作。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 拆下螺栓 (2)、盖 (3) 和垫圈。
- 拆下螺栓 (3B )和伺服阀 ( 2B)。
- 拆下螺栓 (1)、电磁阀 ( 1A)、 O 形密封圈和锥形垫圈。
Show/hide table
图 2 g01284386 - 将螺栓 (5) 从法兰 (6) 上拆下。
- 将法兰 (6) 从壳体 (4) 上拆下。
Show/hide table
图 3 g01284387 - 将螺栓 ( 8 )和 O 形密封圈 (9A )从泵头 ( 7 )上拆下。
- 从壳体上拆下泵头 (7)。
- 拆下连接器 (9)。
Show/hide table
图 4 g00875055 注: 为了便于安装,请标记配流盘 (11) 的正确位置。
- 将 O 形密封圈 (10 )从泵头 (7) 上拆下。
- 将配流盘 (11) 从泵头 (7) 上拆下。
Show/hide table
图 5 g00875056 Show/hide table图 6 g00875132 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 将 O 形密封圈 (12) 从缸盖 (7) 上拆下。
- 从缸盖 (7) 上拆下安全阀 (13)。 将 O 形密封圈 (14) 从安全阀 (13) 上拆下。
- 将测试端口 (15) 从缸盖 (7) 上拆下。 将 O 形密封圈 (16) 从测试端口 (15) 上拆下。
- 从缸盖 (7) 上拆下补偿器阀 (22)。
- 将挡圈 (18) 和 (20) 从补偿器阀 (22) 上拆下。 将弹簧 (19) 从补偿器阀 (22) 上拆下。
- 将控制活塞 (17) 从缸盖 (7) 上拆下。
- 将 O 形密封圈 (21) 从补偿器阀 (22) 上拆下。
Show/hide table
图 7 g00875130 - 将旋转组件 (23)从壳体 (4 )上拆下。
Show/hide table
图 8 g00875175 注: 为了便于安装,请标记活塞 (24) 的位置。
- 将活塞 (24) 从挡板 (25) 上拆下。
Show/hide table
图 9 g00875182 - 将球窝接头 (26) 从泵筒组件 (27)上拆下。
Show/hide table
图 10 g00875186 - 将弹簧组件 (28) 和垫片 (29) 从泵筒组件 (27 )上拆下。
Show/hide table
图 11 g00875193 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 使用工具 (B) 与合适的压力机将挡圈 (30) 从泵筒 (27) 上拆下。
Show/hide table
图 12 g00875194 - 将垫圈 (31) 和弹簧 (32) 从泵筒 (27) 上拆下。
Show/hide table
图 13 g00875204 - 将挡圈 (33) 从壳体 (4) 上拆下。
Show/hide table
图 14 g00875220 注: 使用工具 (D) 拆下密封件 (34)。
- 将密封件 (34) 从壳体 (4) 上拆下。
Show/hide table
图 15 g00875224 - 将挡圈 (35) 从壳体 (4) 上拆下。
- 将轴组件 (36) 和O 形密封圈 (37) 从壳体 (4) 上拆下。
Show/hide table
图 16 g00875537 - 拆下旋转斜盘组件 (38)。
Show/hide table
图 17 g00875538 - 拆下滑块 (39)、杆 ( 40)、和轴承 (41)。
Show/hide table
图 18 g00875539 - 拆下轴承 (42)。
Show/hide table
图 19 g00875564 - 拆下螺塞组件 (44 )和连接销 ( 43)。
- 对于另一侧,重复步骤 31。
Show/hide table
图 20 g00875567 - 拆下螺栓 (45) 和伺服阀 (46)。
Show/hide table
图 21 g00875568 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 使用工具 (A) 和适当的压力机拆下挡圈 (47)。
Show/hide table
图 22 g00875569 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 使用工具 (C) 和适当的压力机拆下环组件 (48)。
Show/hide table
图 23 g00875570 - 拆下弹簧座 (49)。 拆下弹簧 (50)、 (51) 和 (52)。 拆下弹簧座 (53)。
Show/hide table
图 24 g00875571 注: 为了便于安装,请测量螺母 (54)。
- 拆下螺母 (54) 和盖 (55)。
Show/hide table
图 25 g00875573 - 从盖 (55) 上拆下 O 形密封圈 (56)。
Show/hide table
图 26 g00875599 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 使用工具 (A) 和适当的压力机拆下挡圈 (57)。
Show/hide table
图 27 g00875601 - 拆下 O 形密封圈 (58) 和环组件 (59)。 拆下弹簧座 (60)。 拆下弹簧 (61)、 (62 )和 (64)。 拆下弹簧座 (63) 和杆 (65)。
Show/hide table
图 28 g00875602 - 拆下螺栓 (66) 和盖 (67)。
Show/hide table
图 29 g00875604 - 从盖 (67) 上拆下 O 形密封圈 (68)。
Show/hide table
图 30 g00877519 - 拆下导向环 (69) 和环 (70)。
Show/hide table
图 1 | g01284385 |
Caterpillar Information System:
953D Track-Type Loader Engine Supplement Flywheel - Install
953D Track-Type Loader Engine Supplement Flywheel - Remove
D6G Series 2 Track-Type Tractor Belts - Inspect/Adjust/Replace
657G Wheel Tractor-Scraper Wheel Tractor Power Train Oil Filter Base (Transmission) - Remove and Install
D6N Track-Type Tractor Hydraulic System Oil Filter - Replace
2006/06/26 Correction to Testing and Adjusting , "Torque Converter Stall - Test" {3101}
D6N Track-Type Tractor Power Train Transmission Hydraulic Control
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Control Valve
D7G Series 2 and D7G Series II Track-Type Tractors Backup Alarm - Test
D7G Series 2 and D7G Series II Track-Type Tractors Brakes, Indicators and Gauges - Test
D6G Series 2 Track-Type Tractor Condenser (Refrigerant) - Clean
D7G Series 2 and D7G Series II Track-Type Tractors Cooling System Coolant Sample (Level 2) - Obtain
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Assemble - Left Side
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Disassemble - Right Side
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Assemble - Right Side
657G Wheel Tractor-Scraper Machine Systems Blower Motor (Air Conditioner and Heater) - Remove and Install
657G Wheel Tractor-Scraper Machine Systems Air Tank - Remove and Install
953D Track-Type Loader Machine Systems Fuel Tank - Remove
657G Wheel Tractor-Scraper Machine Systems Evaporator Coil - Remove and Install
657G Wheel Tractor-Scraper Machine Systems Heater Coil - Remove and Install
3176C Engines for Caterpillar Built Machines Sensors and Electrical Connectors
953D Track-Type Loader Machine Systems Fuel Tank - Install
D6G Series 2 Track-Type Tractor Additional Messages
D6N Track-Type Tractor Hydraulic System Bulldozer Brace