Flywheel - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7574 | 连杆支架 | 1 |
B | - | 导向螺柱 1/2 - 20 x 5 in | 2 |
C | 7X-2557 | 螺栓 | 2 |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
- 将工具 (A) 和适当的起吊设备连接到飞轮 (4)。 飞轮 (4) 的重量约为
75 kg (165 lb) 。 - 安装工具 (B) ,以便支撑飞轮 (4)。 定位飞轮 (4)。
Show/hide table
图 2 g01284207 - 安装螺栓 (5)。 使用工具 (C) 和适当的撬杆将螺栓 (5) 拧紧至扭矩
120 ± 10 N·m (89 ± 7 lb ft) 。Show/hide table图 3 g01284480 - 安装传感器 (2),直到传感器接触到齿轮轮齿。 逆时针拧松传感器 (2) 大约 3/4 圈。 拧紧螺母 (3) 至扭矩为
25 ± 5 N·m (18 ± 4 lb ft) 。 - 连接线束组件 (1)。
Show/hide table
图 1 | g01284100 |
结束:
- 安装泵驱动连接器。 请参考拆解和组装, "泵驱动接头 - 拆卸和安装"。
Caterpillar Information System:
953D Track-Type Loader Engine Supplement Flywheel - Remove
D6G Series 2 Track-Type Tractor Belts - Inspect/Adjust/Replace
657G Wheel Tractor-Scraper Wheel Tractor Power Train Oil Filter Base (Transmission) - Remove and Install
D6N Track-Type Tractor Hydraulic System Oil Filter - Replace
2006/06/26 Correction to Testing and Adjusting , "Torque Converter Stall - Test" {3101}
D6N Track-Type Tractor Power Train Transmission Hydraulic Control
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Control Valve
D7G Series 2 and D7G Series II Track-Type Tractors Backup Alarm - Test
D7G Series 2 and D7G Series II Track-Type Tractors Brakes, Indicators and Gauges - Test
D6G Series 2 Track-Type Tractor Condenser (Refrigerant) - Clean
D7G Series 2 and D7G Series II Track-Type Tractors Cooling System Coolant Sample (Level 2) - Obtain
D7G Series 2 and D7G Series II Track-Type Tractors Cooling System Coolant Sample (Level 1) - Obtain
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Disassemble - Left Side
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Assemble - Left Side
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Disassemble - Right Side
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Assemble - Right Side
657G Wheel Tractor-Scraper Machine Systems Blower Motor (Air Conditioner and Heater) - Remove and Install
657G Wheel Tractor-Scraper Machine Systems Air Tank - Remove and Install
953D Track-Type Loader Machine Systems Fuel Tank - Remove
657G Wheel Tractor-Scraper Machine Systems Evaporator Coil - Remove and Install
657G Wheel Tractor-Scraper Machine Systems Heater Coil - Remove and Install
3176C Engines for Caterpillar Built Machines Sensors and Electrical Connectors
953D Track-Type Loader Machine Systems Fuel Tank - Install
D6G Series 2 Track-Type Tractor Additional Messages