Pump Mounting - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
B | 8T-5255 | 液压千斤顶 | 1 |
C | 1U-9200 | 操纵杆滚轮举倾机构 | 1 |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将工具 (A)、工具 (C) 和适当的起吊设备固定到泵和安装件组件 (29) 上。 泵和安装件组件 (29) 的重量约为
318 kg (700 lb) 。 - 放置泵和安装件组件 (29)。 安装导管和螺栓 (31)。 安装螺栓 (30)。
Show/hide table
图 3 g01283457 - 连接软管组件 (28)。
Show/hide table
图 4 g01283267 - 从飞轮壳体 (26) 上拆下工具 (B)。
Show/hide table
图 5 g01283448 - 安装支架 (27)。
Show/hide table
图 6 g01283265 泵组件的底部视图 - 连接卡箍 (24) 并安装螺栓 (25)。
Show/hide table
图 7 g01283256 - 定位支撑组件 (23) 后安装螺栓 (22)。
Show/hide table
图 8 g01283245 Show/hide table图 9 g01283255 - 将工具 (A) 和适当的起吊设备连接到蓄电池箱组件 (20) 上。 蓄电池箱组件的重量约为
77 kg (170 lb) 。 - 放置蓄电池箱组件 (20)。
- 安装安装螺栓 (21)。 对另一侧重复上述步骤。
Show/hide table
图 10 g01283243 - 连接电缆组件 (18) 和卡箍 (19)。
Show/hide table
图 11 g01283062 - 定位盖 (17),然后安装螺栓 (16)。
Show/hide table
图 12 g01282889 - 连接线束组件 (15)、卡箍 (14) 和软管组件 (13)。
Show/hide table
图 13 g01282881 - 连接软管组件 (11) 和管组件 (12)。
Show/hide table
图 14 g01282875 - 连接软管组件 (9) 和接头 (10)。
Show/hide table
图 15 g01282855 Show/hide table图 16 g01282868 - 连接软管组件 (7) 和 (8)。
Show/hide table
图 17 g01282853 - 连接软管 (5) 和软管组件 (6)。
Show/hide table
图 18 g01282851 - 连接弯头 (2) 和 (4)。 连接软管组件 (3)。
Show/hide table
图 19 g01282850 - 连接软管组件 (1)。
- 向液压油箱注油。 请参阅操作和保养手册, "液压系统机油 - 更换"。
Show/hide table
图 1 | g01283473 |
Show/hide table
图 2 | g01283472 |
结束:
- 降下驾驶室。 请参阅拆解和组装, "驾驶室 - 倾斜"。
Caterpillar Information System:
953K Track-Type Loader Power Train Pump Drive Coupling - Remove and Install
631G and 637G Wheel Tractor-Scrapers Machine Systems Fan Drive
D6G Series 2 Track-Type Tractor Engine Air Filter Primary Element - Clean/Replace
D6G Series 2 Track-Type Tractor Power Train Brake System - Test and Adjust
D6G Series 2 Track-Type Tractor Power Train Steering Control Valve - Test and Adjust
D6G Series 2 Track-Type Tractor Engine Air Precleaner - Clean
D6G Series 2 Track-Type Tractor Engine Crankcase Breather - Clean
2006/11/27 The 285-0910 Multi-Tool Gp Incorporates Four Diagnostic Tools into a Single, Hand Held Unit {0774, 0779, 0781, 0782}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Hydraulic System
D6G Series 2 Track-Type Tractor Engine Oil and Filter - Change
657G Wheel Tractor-Scraper Wheel Tractor Power Train Speed Sensor (Transmission) - Assemble
657G Wheel Tractor-Scraper Wheel Tractor Power Train Speed Sensor (Transmission) - Disassemble
D6G Series 2 Track-Type Tractor Power Train Transmission Control Linkage - Adjust
D6G Series 2 Track-Type Tractor Cutting Edges and End Bits - Inspect/Replace
D6N Track-Type Tractor Power Train Torque Converter and Pump Drive Housing
D6G Series 2 Track-Type Tractor Cooling System Coolant Level - Check
D6G Series 2 Track-Type Tractor Cooling System Coolant Extender (ELC) - Add
D6N Track-Type Tractor Power Train Oil Filter (Power Train)
657G Wheel Tractor-Scraper Machine Systems Metering Pump (Steering) - Remove and Install
657G Wheel Tractor-Scraper Machine Systems Steering Link Bearings - Remove and Install
D6G Series 2 Track-Type Tractor Cooling System Coolant (ELC) - Change
D5R Track-Type Tractor Power Train Drive Shaft
2006/07/03 The Routing of the Hitch Harness Assembly and the Chassis Harness Assembly Are Improved {1408}
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Modulating Valve (Transmission Clutch)