Ether Starting Aid
Show/hide table
 | |
| Illustration 1 | g01277614 |
(1) Use a minimum radius of 12.0 mm (0.47 inch) at all bends in order to prevent collapsing of the tube throughout routing.
(2) 7N-0296 Ether Cylinder As
- Volumetric capacity ... 1020 cc (62.2 in3)
- Minimum burst pressure ... 7000 kPa (1025 psi)
- Maximum operating pressure at 35 °C (95 °F) ... 1000 kPa (145 psi)
- Relief valve setting ... 2900 ± 410 kPa (420 ± 60 psi)
- Minimum burst pressure ... 7000 kPa (1025 psi)
Show/hide table
 | |
| Illustration 2 | g01277655 |
(3) 3E-6333 Ether Start Valve
- Nominal voltage ... 24 VDC
- Current at 24 VDC ... 4 Amp
- Resistance ... 6 Ω
- Current at 24 VDC ... 4 Amp
Show/hide table
 | |
| Illustration 3 | g01277615 |
View A-A | |
(4) Install the 251-4345 Ether Atomizer As so that the spray orifice is pointing into the incoming air stream.
Caterpillar Information System:
631G and 637G Wheel Tractor-Scrapers Machine Systems Ether Starting Aid
Installation Instructions for the 290-3535 Handrail and Step Gp (Kit) (Cab, Front Access), the 291-1770 Handrail and Step Gp (Kit) (Cab, Front Access) and the 290-3543 Handrail and Step Gp (Kit) (Cab, Front Access){7254, 7256} Installation Instructions for the 290-3535 Handrail and Step Gp (Kit) (Cab, Front Access), the 291-1770 Handrail and Step Gp (Kit) (Cab, Front Access) and the 290-3543 Handrail and Step Gp (Kit) (Cab, Front Access){7254, 7256}
966H and 972H Wheel Loaders Roading Fender Hinges - Lubricate - If Equipped
631G and 637G Wheel Tractor-Scrapers Machine Systems Air Lines
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Starting with Auxiliary Start Receptacle - If Equipped
IT38H Integrated Toolcarrier and 938H Wheel Loader Work Tool Positioner
IT38H Integrated Toolcarrier and 938H Wheel Loader Equipment Lowering with Engine Stopped
IT38H Integrated Toolcarrier and 938H Wheel Loader Articulation Bearings - Lubricate
631G and 637G Wheel Tractor-Scrapers Auger Hydraulic System Auger Hydraulic System
657G Wheel Tractor-Scraper Engine Supplement Engine - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Towing the Machine
D6G Series 2 Track-Type Tractor Lifting and Tying Down the Machine
657G Wheel Tractor-Scraper Engine Supplement Engine - Install
657G Wheel Tractor-Scraper Engine Supplement Water Temperature Regulator - Remove and Install
657G Wheel Tractor-Scraper Engine Supplement Water Pump - Remove
657G Wheel Tractor-Scraper Engine Supplement Water Pump - Install
Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095} Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}
2006/06/19 New Bolts Are Now Used On the Rollover Protective Structure {7325}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Solenoid Valve (Differential Lock)
631G and 637G Wheel Tractor-Scrapers Machine Systems Water Lines
657G Wheel Tractor-Scraper Engine Supplement Engine Support (Rear) - Remove and Install
631G and 637G Wheel Tractor-Scrapers Auger Hydraulic System Gear Pump (Auger)
D6N Track-Type Tractor Hydraulic System Steering and Transmission Control
The Transmission Wiring Harness May Fail on Large Wheel Loaders{1408, 3073} The Transmission Wiring Harness May Fail on Large Wheel Loaders{1408, 3073}