Drive Shaft (Center) - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 155-3597 | Wheel Chock | 4 |
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
- Park the machine on a flat, level surface. Lower the grapple and the decking blade to the ground. Position Tooling (A) on both sides of the rear wheels of the machine.
Show/hide table
Illustration 1 g01273511 - Remove bolts (1) from yoke (2). Repeat this Step for the opposite end of drive shaft (3) and remove drive shaft (3).
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 155-3597 | Wheel Chock | 4 |
Show/hide table
NOTICE |
---|
When the center drive shaft is installed, it must be installed in phase with the rear drive shaft. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and the lubricating fittings are aligned. |
- Position drive shaft (3) and install new bolts (1). Make sure that drive shaft (3) is properly seated in yoke (2) before tightening bolts (1).
- Tighten bolts (2) in a crisscross pattern to a torque of
120 ± 20 N·m (90 ± 15 lb ft) . Repeat this Step a second time. - Repeat Steps 1 and 2 for the opposite end of drive shaft (3).
- Remove Tooling (A) from the rear wheels of the machine.
Show/hide table
Illustration 2 | g01273511 |
End By:
- Disconnect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
D8T Track-Type Tractor Machine Systems Fast Fill Fuel Adapter
D8T Track-Type Tractor Machine Systems Fast Fill Fuel Adapter
631G and 637G Wheel Tractor-Scrapers Auger Hydraulic System Gear Pump (Auger)
3508 EUI Engine for Off-Highway Truck/Tractors Auxiliary Water Pump
657G Wheel Tractor-Scraper Machine Systems Push-Pull Hook - Remove and Install
854K Wheel Dozer Cooling System Coolant (ELC) - Change
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer CID 2766 FMI 02 Intermediate Engine Speed Switch erratic, intermittent, or incorrect
3508 EUI Engine for Off-Highway Truck/Tractors Fan Drive
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Case and Parts Group
C4.4 Industrial Engine Flywheel Housing - Inspect
D6G Series 2 Track-Type Tractor Hydraulic System Bulldozer Lift Control Valve
C4.4 Industrial Engine Flywheel - Inspect
657G Wheel Scraper Power Train Drive Shaft - Remove and Install
854K Wheel Dozer Safety Messages
3508 EUI Engine for Off-Highway Truck/Tractors Cylinder Block
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer Engine Temperature Sensor Open or Short Circuit - Test
C4.4 Industrial Engine Air Inlet and Exhaust System - Inspect
2006/05/29 Updated Plate Assembly Eliminates Interference For the Cable On the Cab Heater {7304}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Retarder Hydraulic Control Valve - Disassemble
657G Wheel Tractor-Scraper Wheel Tractor Power Train Retarder Hydraulic Control Valve - Assemble
657G Wheel Scraper Power Train Retarder Hydraulic Control Valve - Remove
657G Wheel Scraper Power Train Retarder Hydraulic Control Valve - Install
2014/08/14 Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
657G Wheel Scraper Power Train Gear Pump (Transmission Scavenge) - Remove